Home > Service Fuser > Lexmark Error 922

Lexmark Error 922

Contents

If cables, connectors and connections are good replace assemblies listed. Load correct size Error 28 Input sensor not made after pick attempt. If this does not clear up the fuser error, the problem may be in one of the following: the fuser cover assembly the engine board the DC fuser cable the fuser Remove jammed media Error 90X Software Error Unrecoverable software error. http://jvmwriter.org/service-fuser/lexmark-922-service-error.html

See if there is any paper or any other item stuck there that could be causing the fuser unit to overheat. So yes it does sound like the hvps. Requires further measurement The printhead (laser scanner) does not contain any serviceable parts. Perform fuser service check. http://support.lexmark.com/index?page=content&id=SO1583

920.06 Service Fuser Error

It's just not transferring from there to the paper. Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. vovanfun 34.194 προβολές 16:42 Vídeo Recarga Toner Lexmark E260 | E360DN | E460DN - Vídeo Aula Valejet.com - Διάρκεια: 4:06. Verify latch relay is operating - slowly close door and listen for interlock switch 3.

Replace the bump alignment motor Replace bump motor Replace interlock switch Replace System Card Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex test). Back to Service Error Code List Source: Lexmark KnowledgeBase Home Page Technical Resources Lexmark Error Codes HP Error Codes Tech Support Blog HP Drivers Lexmark Drivers Terms & Conditions Product Lexmark Fuser Replacement Remove jammed media How did we do?

Replace with the correct printhead. Lexmark 924.01 Service Fuser Error Check the continuity of the fuser lamp at the two heavy leads. by pedrohuerta on Jun 2, 2005 at 3:59pm Add comment Please sign in to comment 0 received reply from lexmark" The “922 Fuser Error” is a cold fuser error. http://support.lexmark.com/index?page=content&segment=SUPPORT&locale=en&userlocale=EN&id=SO5058&productCode=LEXMARK_T656 If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact.

Check the fuser lamp is the correct type of lamp that should be installed. • Verify the line voltage is not exceeding the maximum rating for the printer. 922.02 Service Fuser Error Note: This error indicates the printer was able to read the cartridge ID, but the ID did not pass the verification test. The HVPS fixed the problem I had. Since you have replaced the fuser twice, LVPS and the Engine board most likely to be the issue with the DC auto connect which goes from the Fuser to the Engine

Lexmark 924.01 Service Fuser Error

Error 25 Input sensor made at wrong time. by Anonymous on Feb 6, 2006 at 12:16pm Add comment Please sign in to comment 0 Another thing you can check is the charge roller located above the toner cartridge. 920.06 Service Fuser Error CreativeCopias 11.848 προβολές 7:47 Lexmark X364dn Unboxing & Setup - Διάρκεια: 18:13. Service Fuser Error Lexmark Printer To order this part please click here.http://www.iteminc.com/itemdesc.asp?i...For any other printer needs visit us at http://www.iteminc.com Κατηγορία Επιστήμη και τεχνολογία Άδεια Τυπική άδεια YouTube Εμφάνιση περισσότερων Εμφάνιση λιγότερων Φόρτωση... Διαφήμιση Αυτόματη αναπαραγωγή

eCommerce Solution : k-eCommerce My Account| Cart| Order Status Market Point Search: select Advanced search Read Customer Reviews GSA Contract Schedule Enter Here Need Assistance? check my blog Verify correct cable connections from the Engine board to the HVPS. Power strips and uninterrupted power supplies can cause a low amperage problem in your printer whichcan trigger a false fuser error. If this isthe first time you have seen the error, turn the printer off. Lexmark X654de Service Fuser Error

I've read a bunch of posts that pertain to this topic, but still haven't figured out how to fix my situation. Transfer Roll Error Cannot start servo operation. Call us with any questions toll-free 866-352-7108 or local 608-831-2396. http://jvmwriter.org/service-fuser/lexmark-920-error-codes.html Make sure that nothing is stuck inside the fuser unit that cancause the fuser unit to overheat.

I tried to print something, but the printer smells like it's burning, the roller below the toner cartidge was caked with toner, and barely anything transferred from the photoconductor to the 122.02 Service Fuser Error If you have other tech support questions that are not covered here, send email to [email protected] This is what Lexmark Tech Support had me do.

I would recommend trying the easy parts first to eliminate your problems.

If the error message goes away with the old fuser unit, please check that the new fuser unit is the correct one for this printer model. A secondary error indication can be obtained by pressing an releasing a button. Sign Up Login Add Question Rubble asked Jun 2, 2005 at 3:39pm 0 Lexmark Optra T614 922 fuser error I have a Lexmark Optra T614 laser printer in an officeI get 925 Service Fuser Error Lexmark T632 viandant5 16.058 προβολές 4:02 lexmark x340 - Διάρκεια: 3:40.

Run the Quick Disk Test. We can email further info if needed for your particular model. It may take the printer 10-20 seconds to determine if the print cartridge is defective. have a peek at these guys Replace Printhead Pricing Error 934 Printhhead Error - Lost Lock condition Indicates a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system

I truly appreciate it.