Home > Printhead Error > Lexmark Optra T612 935 Printhead Error

Lexmark Optra T612 935 Printhead Error

Contents

Governor: An expert whose answer got voted for 20 times. Privacy Policy Terms of Use Sonic AskHomeSearchSearchHomehow significant female agency king learadmin October 18, 2016October 18, 2016Comments Off on how significant female agency king learhow significant female agency king lear high Replace low voltage power supply assembly. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. http://jvmwriter.org/printhead-error/lexmark-optra-t612-printhead-error.html

Install more memory Simplify print job Delete fonts, macros and other data stored in RAM Error 39 Page too complex to print.To verify that the printer recognizes all the installed memory, this is a printhead error and can be caused by the scanner or the engine board. It will need to be replaced. Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex Unit. pop over to these guys

935 Service Printhead Error Lexmark E352dn

It will need to be replaced. It may take the printer 10-20 seconds to determine if the print cartridge is defective. test). Run the Quick Disk Test.

Make sure the memory shown on the printout matches the installed memory. Error 54 Serial Error - Framing or parity error on serial. See “Duplex” on page 2-16 Error 24 The defined paper size is too short to print data as formatted. Lexmark T640 933 Service Printhead Error Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the down position if applicable to your machine.

Any ideas? Aug 13, 2013 | Lexmark Optra S 1625 Laser Printer 2 Answers 935 Service Printhead error Error 935 Printhead Error - Mirror motor unable to reach operation speed Check cables, look Shop for Lexmark print cartridges Error 32 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer. Error 930 The wrong printhead is installed.

How do I fix this. Lexmark T650 Printhead The printhead is the actual laser scanner unit which is under the top cover. Error 24X Paper Jam - Check Tray "X" Primary: Paper is jammed around Tray X (X=tray 1 thru 5). It's a very superb machine and I need to use it again.

931.01 Service Printhead Error

Error 26 Duplex unit is installed but paper tray is not sensed. Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about Lexmark Optra T612 Laser Printer 1 Answer 935 Service Printhead Error - Lexmark 935 Service Printhead Error Lexmark E352dn Remove the duplex front cover to access the jam area. 935.10 Service Printhead Error Lexmark Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time.

Shop for Lexmark Maintenance kits * This is a model dependent interval Install maintenance kit and reset maintenance message Purchase Lexmark maintenance kits How did we do? http://jvmwriter.org/printhead-error/lexmark-933-printhead-error.html Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers If the test fails, the disk is defective or the data on track1 is bad. Your cache administrator is webmaster. Service Printhead Error Lexmark E450dn

Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed. Error 7X Network Card Codes These user codes are documented in various network card user manuals. Error 921 Fuser is below standby temperature when idle. this content Search Fixya Press enter to search.

Question about Lexmark Optra Printers & Copiers 2 Answers 935 service printer head ...how do I fix it? 935.26 Service Printhead Error Reconnect. Also, feed wheels (2) for 4049 duplexer need replacing.

If the error appeared while sending a job from the host to the printer, turn the printer off, then turn it on and try again.

Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. I've seen several where the motor board burns up. Check the wiring harness cable. Lexmark T650 Printhead Replacement Or just drag it here!

Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22. Error 53 Unformatted or Defective Flash - Flash problem at POR or while attempting to write. If an open circuit, replace the lamp or fuser. have a peek at these guys I guess there is always a first time.

Error 7X Network Card Codes These user codes are documented in various network card user manuals. Error 920 920 Fuser Error Fuser is below temperature while printing. We got it this morning and I have it installed. You'll be helping the wider internet too.

Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed. Check connections to the to interconnect card assembly. Or just drag it here! See “Duplex” on page 2-16 Error 24 The defined paper size is too short to print data as formatted.

I will have purchasing call in an order. Replace the transfer roller as necessary. Lexmark Optra T614 Laser... 1 Answer 194 SERVICE CODE CDC Lexmark Optra SC 1275 Laser... 1 Answer Load MP Feeder Lexmark Optra M412 Laser... 1 Answer 929 service toner sensor error It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer.

The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up. Yes No Cancel Update (+2 points) You can't post conmments that contain an email address. × Comment Anonymously Video Images 1 Answer Col Johnson Level 2: An expert who has achieved If you decide to try use a very very small amount of lubricant because if you use to much it tends to splatter on the optics and then the laser/scanner (printhead) Replace the disk if instructed by the operator panel.