Home > Printhead Error > Lexmark 4039 Printhead Error

Lexmark 4039 Printhead Error

Contents

The printer has PostScript and PCL emulation standard. Remove the outer EMC shield by pressing down on the two bottom tabs, slide the shield forward, then down (10P has no outer EMC shield). Il personale di assistenza autorizzato, consapevole di ciò, deve adottare le precauzioni necessarie. Page 136: Printhead Window Cleaning Procedure, Cleaning The Transfer Roller 4039-1XX Printhead Window Cleaning Procedure Do not use cleaning fluids on the printhead window. check over here

Replace network card 1. 973 Network Card 2 Network care 2 EEPROM/NVRAM failure. Make sure the memory shown on the printout matches the installed memory. 38 Memory Full Memory used to store pages is full. To print the manual completely, please, download it. Page 79 4039-1XX Repair Information... http://support.lexmark.com/index?page=content&productCode=LEXMARK_T642&segment=SUPPORT&userlocale=EN_US&id=SO3398

935 Service Printhead Error Lexmark E352dn

Enter Diagnostics mode. 2. Check for +5VDC at J8-1 and for +34VDC at J9-1 and at J11-4. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Letter size paper # 10 envelopes Symbol Set Roman-8 1.

An easy fix! - Διάρκεια: 7:47. Some unauthorized lubricants may chemically attack polycarbonate parts. The display goes through a continuous sequence of turning pels on and off. 5. Service Printhead Error Lexmark E450dn Select [Sensor Test]. 3.

The specific error is Download Emulation CRC Failure. Failure Service Manual Action Network card is installed but is not communicating with the system board. Page 144 4039-1XX Asm- Part Index Number 1381120 1381001 1381046 1381047 1381121 1381002 1381049 1381122 1381003 1381623 1325614 1329515 1408672 1328503 1328441 1623642 1623642 1328244 1624875 1328243 1039391 1329013 1383316 1383314 http://support.lexmark.com/index?page=content&id=SO3848 If this error returns after a POR, there is a software or microcode incompatibility problem.

Page 12: Safety Information 4039-1XX Safety Information • The maintenance information for this product has been prepared for use by a professional service person and is not intended to be used 935.10 Service Printhead Error Lexmark Remove the operator panel mounting screws from the inside of the top cover. Remove the right, left, and top covers. 4. Remove the top cover. 4.

Service Printhead Error Lexmark T650n

Do Not replace the card. Page 118: Transfer Roller Housing 4039-1XX Transfer Roller Housing Paper Guide* * Transfer roller housing for 10P has no paper guide Service Manual... 935 Service Printhead Error Lexmark E352dn Page 110: Zif Connector Removal 4039-1XX Zif Connector Removal 1. 933 Service Printhead Error Page 114: Duplex Option System Card And Motor Removal 4039-1XX Duplex Option System Card And Motor Removal 1.

System board Vertical Void or Streak Do a developed image test to determine if the defect is occurring before or after the transfer process. check my blog E6 Engine ROM check sum error. Run the diagnostic test for the input and exit sensors replace as necessary. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. 931.01 Service Printhead Error

Enter Diagnostics mode 2. Page 187: Table Of Contents 4039-1XX page count 41 paper drawer base assembly, 500-sheet 151 optional (500-sheet) assembly paper feed alignment gears assembly 143 assembly 139 drive assembly 145 magnet adjustments To view this page ensure that Adobe Flash Player version 10 or greater is installed. http://jvmwriter.org/printhead-error/lexmark-933-printhead-error.html U.S.

values. Lexmark T650 Printhead Disconnect the cable from the HVPS connector. 7. Open the top cover and remove the print cartridge. 3.

Replace the engine board. 956 Configuration ID Indicates a problem with the Configuration ID.

Page 86: Fuser Removal, Fuser Input Guide Removal 4039-1XX Fuser Removal Note: The heater lamp is fragile and may be damaged if you are not careful when you remove or replace Pivot the printhead around the shoulder screw [B] until the skew marks on the printout are parallel to the top edge of the paper. Select [Device Test] 3. 931.01 Service Printhead Error Dell Press Return to stop continuous LCD test.

Check the continuity of the cable before replacing the sensor. If the error appears again, call the next level service support for assistance. 917 Transfer Roll Error Cannot start servo operation. Remove the power switch rod. have a peek at these guys Page 105 4039-1XX Repair Information...

Page 150 4039-1XX Asm- Part Index Number 3-26 1381099 1381134 1381095 1383314 1325138 1325067 1328467 Service Manual Units Description Cable, Output Bin/Operator Panel 12L(handle mounted sensor) Cable, Output Bin/Operator Panel 16L(handle Replace the system board. 954 Engine Board Printhead crystal not functioning correctly. This manual also for: 4039 - b/w laser printer Comments to this Manuals Your Name Enter your comment: Symbols: 0 Enter text from picture: Write a comment Latest comments: × Bookmark This cable is not present in all models. 5.

Page 30: Blank, Blank Page 4039-1XX Blank Page Inspect the printhead shutter for proper operation and make sure the actuator on top of the cartridge is present and extends into the Page 93 4039-1XX Repair Information... Verify that the network card is installed and grounded correctly. If this error returns after a POR, there is a software or microcode incompatibility problem.

Print quality can be affected if the gears are too tight. If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact. Jason MrKaramell 19.952 προβολές 7:03 Lexmark T630 T632 T634 Fuser Maintenance Kit Replacement - Διάρκεια: 5:40. Unrecognizable Network Card x.

Lost lock condition. Lift the sensor to unsnap it. Application Error en We're sorry for the inconvenience. U6: NON-VOLATILE MEMORY FAULT data scrambled.