Home > Paper Jam > Lexmark Duplex Setting Error

Lexmark Duplex Setting Error

Contents

Mirror motor unable to reach operational speed, various other component level failures indicated by 935.XX Check cables, look for chafing or damage to ribbon cable at sharp bends around rear Error 901 Engine Flash Indicates the Flash with the system code program is defective Replace System Board Request Quote Error 914 DC Pick Motor - No Encoder Feedback Check the Verify latch relay is operating - slowly close door and listen for interlock switch 3. Check fan for binding or defective bearing - Replace Fan How did we do? weblink

it Ci scusiamo per l'inconveniente. Please try the request again. There should be zero ohms resistance between the transfer roll shaft and the high voltage supply contact. de Wir entschuldigen uns für die Unannehmlichkeiten. http://support.lexmark.com/index?page=content&id=SO2047

Lexmark T654 Duplex Unit

Error 62 Disk Full Not enough disk space for data that has been requested to be written to disk. es Lamentamos las molestias. br Lamentamos o inconveniente.

Replace the assys in the following order 1. Remove jammed media Error 250 Paper Jam - Check MP Feeder Paper is jammed in the multipurpose feeder. Replace printhead, system board or ribbon cable. Lexmark T640 Duplex Unit Error 80 Network Card Codes These user codes are documented in various network card user manuals.

Es gab einen Fehler bei der Anwendung. Lexmark Printer Paper Jam But No Paper Thank you and your firm again, you were terrific. Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 927 Main Fan Stalled, Cartridge Fan or RIP fan stalled, Power off and manually spin fan - it http://support.lexmark.com/index?pmv=print&page=content&locale=en&userlocale=EN_US&id=SO4955 If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed.

Application Error en We're sorry for the inconvenience. Lexmark Printer Paper Jam Problem Also, can I get some instructions on putting in the rollers. Replace fuser assembly Replace Fuser Lexmark Fuser Error 145.XX (C520X/530X) Motor bump aligner service check 1. Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22.

Lexmark Printer Paper Jam But No Paper

Error 54 Serial Error - Framing or parity error on serial. Replace Printhead Pricing Error 936 Error 937 Error 936/937 Main Drive Motor, Transport Motor An error with the main drive motor has been sensed by the printer Optra s 2450 Optra Lexmark T654 Duplex Unit Lexmark Fuser Pricing Error 925 A 925 service error indicates the wrong fuser lamp is installed in the printer and does not match the one stored in the printer code. 230.02 Paper Jam The transfer roller is included in the maintenance kit.

It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer. http://jvmwriter.org/paper-jam/lexmark-error-241.html Also, if the accumulated sheets are removed, the portion of the job printed after the jam will not be stapled. Replace Printhead Pricing Error 932 Lost hsync No High voltage signal - check connections at both ends of cable for corrosion or oxidation. Check the operation of the toner sensor. Paper Jam Duplexer Kyocera

Error 44 Defective font card installed in font slot. Make sure there is no paper jammed in the printer. Try opening Tray X. check over here Check paper sensor flag for restricted movement or damage.

Error 52 Flash Full - Not enough flash memory for data requested to be stored. Lexmark Printer Keeps Saying Paper Jam Error 47 47 Font Card Removed While Printing Printer needs data on removed card. If the Quick Disk Test passes but the disk does not work, run the Disk Test/Clean (2 hr.

Es gab einen Fehler bei der Anwendung.

Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Power printer off one to two minutes. Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. Lexmark Error Codes If the error appeared while sending a job from the host to the printer, turn the printer off, then turn it on and try again.

The pin should enter the tower on the HVPS and depress the cover switch. See “Network Wrap Tests” on page 23. C'è stato un errore con l'applicazione. this content Your cache administrator is webmaster.

If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact. Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed. Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults. Error 43 Font card format not supported by printer.

Se ha producido un error en la aplicación. Additional info on X and XX codes available by email. Replace low voltage power supply assembly.