Lexmark Printer Error Code 0502
Issues that occur with the A960 and A940 all-in-one printers are typically fair and simple to fix. Now I won't have to go to Dell for cartridges. Re-connect the power supply to the All-In-One. 10. As for everyone else, that lands on this post in the future......I had this error on my Dell A940 (all in one) I cleaned the rail bar with a light furniture http://jvmwriter.org/lexmark-printer/lexmark-printer-0502-error.html
Liu Kastiju 15.033 προβολές 13:20 Lexmark 5150 - Διάρκεια: 0:26. The magenta ( red ) does not work. This one still prints black, blue and yellow fine. Disconnect the power cable from the back of the Lexmark X5100 / X6100 Series. http://support.lexmark.com/index?productCode=LEXMARK_X5150&segment=SUPPORT&page=content&id=HO2707
Leave the power cable disconnected for 30 seconds. 4. press check to print alignment page. A drag in the cartridges might also cause an error message.
CAREFUL NOT TO PULL OUT THE THREE WIRE STRIPS IN THE PROCESS.3) Under where the scanner bed sits, the three wire strips go into the printer behind a door about 4 While this blog was interesting, and I had tried to clean the unit previously, I went back and cleaned it again and then a second time lubricating the rail. Perform the hardware test without cartridges first and then with both cartridges. Love that I keep finding instructions online to keep this beast going and going. - Nitecat Hi MattThanks for your instructions - a bit beyond a Grandma but fortunately my son
Can anyone peek back there and tell me where it was connected and any other information to help me get it back in? more detail Request a call back Digital Home Plan $119.99 3PCs and 2 Mobile Devices Unlimited Support +TechGenie PC Optimizer/Support Dock valid for 5 Years for $30 $149.99 Limited Period I didnt' pay for tech support. The unit does not have a paper jam.
LexmarkListens 62.971 προβολές 2:30 OVNI GIGANTE GRABADO EN UNA FAENA MINERA EN COPIAPO. - Διάρκεια: 1:23. Leave the power cable disconnected for 30 seconds. • Slide the cartridge carrier to the middle of the printer by taking the top part of the belt and moving it gently After this, push the encoder strip down and back up in order to get it back into the correct slot located on the back of the ink cartridge carrier. Press Select.
Seems I got the error message after installing a new (genuine) 82 cartridge.
Diagnostic & repair for your technologies. Swapped back the old one, but was still problematic. My printer is old...like 2001....and so is the Dell.
Simple fast and easy way to get your printer to print. - Διάρκεια: 2:19. check my blog It is not broke. The cartridge holder is stuck a little right of center and will not move/slide. After this, unplug the printer and check whether any paper is jammed inside.
Take out both cartridges. 6. Slightly push the encoder strip down and then back up to get it into the slot. 8. Bestsellers in touch screen printers Over the last few years or so, touch screens ... this content Take out both cartridges. • Place an index finger on the encoder strip on either side of the cartridge carrier. • On the back of the cartridge carrier, there is a
Good luck! But it so hard to put it somewhere, where you can't even see. Feedback Like Dislike Comments Thanks for submitting your Feedback Request a call back Please fill up the following details and one of our tech experts will get in touch with you.
Internet Explorer could not...
turn printer on.14. I let it soak for a bit, then carefully rinsed it with hot water on very very low setting.I cleaned up what dust I could and some ink on a plastic Also clean the contacts of the printer. 10. Could you please provide instuctions on how to fix this, as stated above.
Now if only I could get paid for it.I STILL don't understand how simply wiping a plastic ribbon with a clean cloth fixes electronics, but it worked one time on one TUTORIALES-MASTER 619.023 προβολές 6:05 recarga lexmark - Διάρκεια: 3:15. The old printer, makes a great doorstop for my daughters room. have a peek at these guys by Anonymous on Mar 15, 2009 at 7:21pm Add comment Please sign in to comment The same thing happen to me.
Il ya eu une erreur à l'application.