Home > Lexmark Printer > Lexmark Printer Error 914

Lexmark Printer Error 914

Contents

Replace Printhead Pricing Error 931 Printhead error - No first sync - check connections at both ends of cable for corrosion or oxidation. Make sure the memory shown on the printout matches the installed memory. iteminc 89.979 προβολές 14:14 MOV01078 - Διάρκεια: 3:49. Error 940 LV Power Supply Low voltage power supply cross over test failed. check over here

Often pulling the tray out and re-insert corrects. Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. However when I try and print from computer, First I get the "status" message as printing, followed by status of Error-Print....Any help Please? Error 59 Duplex Cover Open Top cover of duplex unit is sensed open. https://www.marketpoint.com/lexmark-error-codes-910-911-912-913-914.aspx

Lexmark Engine Error

Now there´s still some other stuff to solve.. To verify that the printer recognizes all the installed memory, go to the user menus and print the Print Menus test page. It is the most likely cause of the problem, followed by the engine/system board.

Replace print head or ribbon cable. Follow that by checking theautoconnect cables and connectors on the drawer option and the printer for any signs of damage. The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up. Scroll Down to your error code....

Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed. Lexmark Dc Pick Motor Also checkthe sensor cable to make sure it iscorrectly connected to the optionsystem board. Error 54 Serial Error - Framing or parity error on serial. http://support.lexmark.com/index?pmv=print&page=content&productCode=LEXMARK_C510&segment=SUPPORTproductCode%253D&viewlocale=en_US&searchid=1285205360214&actp=search&userlocale=EN_BE&id=SO3172 POR several times Check each board for secure ground.

Any other suggestions? The main motor is located just to the left of the toner cartridge. Run the Quick Disk Test. See “Network Wrap Tests” on page 23.

Lexmark Dc Pick Motor

Printer randomly and recurringly reports that Tray1 is missing. Check paper sensor flag for restricted movement or damage. Lexmark Engine Error Verify correct cable connections from the Engine board to the HVPS. Lexmark Error Codes Replace the Auto compensator Assy.

If the test fails, the disk is defective or the data on track1 is bad. http://jvmwriter.org/lexmark-printer/lexmark-printer-error-200-11.html coz I'm sick of trying to fix it!greg by greg9 on Aug 1, 2005 at 2:16am Add comment Please sign in to comment 0 Could be a problem with the paper What's New? When i turn it on i get the error code 913, Service motor.

Make sure there is no paper jammed in the printer. ERROR 22 The exit sensor was not unmade in time. POR several times Check each board for secure ground. this content I went through the manual, and today I replaced the pick arm assembly.

remote pc repair remote support right management services router server server help server support sharepoint slow computer small business small business events small business news small business support software installation software It says that it is a ... If cables, connectors and connections are good replace assemblies listed.

May require service technician Press “GO” to clear message and temporarily continue Install Printer Transfer Drum Unit Error 88 Toner Low Toner sensor detects low toner.

I then get the error message 200. If the errordoes not return, continue using the printer as before. Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed. Error 22 The exit sensor was not deactivated in time.

This is a common problem. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Error 921 Fuser is below standby temperature when idle. have a peek at these guys Error 30 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed properly and that it is detected by the ramp on

Remove anyjammed sheets of paper from theprinter and check the pass thrusensor and flag for proper operationby running the appropriate TraySensor Test from the diagnosticsmenu. Check AC power source for noise. Lexmark Fusers Error 924 924 Fuser Error - Open circuit detected in thermistor circuit. Se ha producido un error en la aplicación.

If you can print from all but one of the paper trays, this is the source of the problem. Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed. Make sure fuse is installed correctly, Verfy proper fuser is being used.