Home > Lexmark Printer > Lexmark Printer Error 0502

Lexmark Printer Error 0502

I don't know if it's worth taking this apart to clean those parts of it that will make a difference in making the Magenta work. SillyReviews Jeff 1.646 προβολές 2:38 Lexmark 83 / Dell 7Y745 Refill Instructional Video - Διάρκεια: 2:05. There is no wanrantie on this printer can I fix this my self Expert: Charles A. They make it sound so easy but is not. http://jvmwriter.org/lexmark-printer/lexmark-printer-0502-error.html

MANUALLY move cartridge carriers towards the center.4. Any other instructions/advice? I have talked to support (overseas) and they were unable to help. Leave the power cable disconnected for 30 seconds. 4. http://support.lexmark.com/index?page=content&id=SO2723

Does anyone know where the encoder strip fits on back of the cartridge slots?.....I'm not able to see, and I think that if I knew this, it would solve my problem. If you are facing the printer and looking inside of the printer, the strip hooks to YOUR left with the arrow facing down. this is usually cause by a twisted encoder strip, or a bad system board.

When I try to test print a page a message says there is a print job in progress but when I open the printing queue there are no jobs pending. Roberts is online now Lexmark printer x6100 says hardware error 0502 what does that Customer Question Lexmark printer x6100 says hardware error 0502 what does that mean Submitted: 5 years ago. Lift the lid of the unit, just below the scanner portion of the All-In-One, to expose the inside of the unit where the printer cartridges are located. 3. Lightly press the strip first to the rear and then forward, if necessary. 9.

Again, the back part of the printer casing goes in first, then the top front casing. Slightly push the encoder strip down and then back up to get it into the slot. 8. If you didn't not want to replace it you would have to take it to a local computer repair shop to get this repaired. How to Perform the Hardware Test on the Lexmark Using the operator panel on the printer: 1.

by unknown on Feb 1, 2007 at 12:11pm Add comment Please sign in to comment I have the very same problem. Used alcohol.I unplugged all wires where I could see that they unplug and plugged them back in. Place an index finger on the encoder strip on either side of the cartridge carrier. 7. Sadique Support Code B200...??? 10/18/2016 10/18/2016 Nathan I have a brother MFC (dual tray), I sometimes receive 10/18/2016 10/18/2016 Russell H.

Mike by flagship112 on Dec 23, 2009 at 6:31am Add comment Please sign in to comment 0 Brilliant, thank you so much, you have just saved me from having to hand by unknown on Jan 31, 2010 at 8:49am Add comment Please sign in to comment 0 I have had a Lexmark X5150. Just followed your post and all is well, for now. CLEAN the shiny silver bar that is connected to the carriers using a dry cloth, from left to right in one direction.9.

Slightly push the encoder strip down and then back up to get it into the slot. 8. check my blog put inks in.15. take cartridges out.5. CLEAN the see-thru tape that is connected to the carriers using a dry cloth, from left to right in one direction. (careful, it is delicate, clean both sides).11.

If my answer did not work please let me know instead of giving negative feedback. If the test works with no cartridges in the printer, run it again with one cartridge at a time installed. and other Printers Specialists are ready to help you Ask your own question now Share this conversation Related Printers Questions Question Date Submitted Model PIXMA MG4160 - LCD message is Support this content it Ci scusiamo per l'inconveniente.

It comes off like this: Don't break anything. I even uninstalled the printer and then reinstalled it. infoguayana 88.947 προβολές 3:15 Impresora Lexmark, ERROR con Cartucho ORIGINAL - Διάρκεια: 3:09.

X Hover 557.289 προβολές 2:19 How To: Clear a Paper Jam on a Top Feeding Lexmark Printer - Διάρκεια: 2:30.

Perform the hardware test without cartridges first and then with both cartridges.* 12. Gently move the top part of the printer belt to the right. 5. characters left: Contact Us|Terms of Service|Privacy & Security|About Us|Our Network © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 6 8123798 Login|Contact Us Printers Printer Repair Questions? unplug power brick.3.

PLease help if you know.Thanks! - Anonymous Clean the rollers the best that you can.This should solve the problem - hanknumb You 502 Error worked great for my Lexmark X5150. On the back of the cartridge carrier, there is a small slot that the encoder strip fits into. characters left: Contact Us|Terms of Service|Privacy & Security|About Us|Our Network © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 125 4845491 Login|Contact Us Computer For Online Computer Support, Ask a Computer Technician Not a Computer have a peek at these guys After about 2 hours of work.

Ask Your Own Computer Question Customer: replied5 years ago. Take out both cartridges. 6. If it fails you know what you would need to do and what your options are. Roberts replied5 years ago.

I had to persuade them to tell me. Reconnect the power cable and switch the printer on again. 11. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. by unknown on Mar 30, 2009 at 2:01am Add comment Please sign in to comment 0 Hi, help needed here,I have a X6150 multifunction printer, after fixing the gear roller the

The printer should print a sheet of paper with one black bar and one grey bar. 4. He also said that lexmark does not carry this part. But it so hard to put it somewhere, where you can't even see.