Home > Lexmark Printer > Laxmark Error

Laxmark Error

Contents

File is too large You have exceeded the amount of data a scan file can hold. Make sure there is no paper jammed in the printer. Error 63 Unformatted or Defective Disk The printer will ignore a disk it senses as defective. Request Quote Error 920 920 Fuser Error indicates the Fuser is below temperature while printing.

For more information, see Installing the print cartridges. Unsupported device In Photo mode, an unsupported device is attached to the DPS port. John D. In general, fuser errors require replacement of the fuser as a cost effective repair. https://www.marketpoint.com/lexmark-error-codes.aspx

Lexmark Printer Error Code Ec5

System Board Pricing Request Quote 975-979 Network Card X Indicate a network card failure in the specified slot, X=any card in slot 1 or 2. 975- Unrecognizable Network Card 976- Unrecoverable ERROR 23 Jam at the duplex unit. If you have other tech support questions that are not covered here, send email to [email protected]

The main motor is located just to the left of the toner cartridge. Replace Printhead Pricing Error 934 Printhhead Error - Lost Lock condition Indicates a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system Engine Board 3. Lexmark Printer Error Lights If you are installing a color cartridge, insert it in the right carrier.For more information, see Installing the print cartridges. Alignment Error The transparent tape is still on the cartridge nozzles.

If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. Lexmark Printer Error Messages Reload the paper and do a power on reset. We stock the full range of Lexmark service parts needed for preventive maintenance and repair service. Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22.

See “Network Wrap Tests” on page 23. 938.06 Service System Electronics Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed. Error 53 Unformatted or Defective Flash - Flash problem at POR or while attempting to write. Blank paper size selected is too small for one of image already selected.

Lexmark Printer Error Messages

Controller Board 2. Insert print cartridges in the correct carrier. Lexmark Printer Error Code Ec5 Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the down position if applicable to your machine. Lexmark Engine Error Replace the Autocompensator Assy.

Cartridge missing No cartridge present in the cartridge carrier. If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages. Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed. Lexmark Error Codes Problem

Error 27 Envelopes/paper loaded are wrong size. Clear the paper jam. Size Warning In Photo mode, resized image is larger than the selected blank paper size. While in Photo mode, a memory card with no images is inserted.

There should be zero ohms resistance between the transfer roll shaft and the high voltage supply contact. Lexmark Ms310dn Error Codes Open the printer rear door to access the jam. Service errors 980 thru 984 < device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. >

The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up.

Los Altos Hills, CA Thank you. Pay close attention to the area where the toner cartridge sits. Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers Lexmark Crc Failed Do Not Power Off Replace low voltage power supply assembly.

Scroll Down to your error code.... The fuser can usually be removed with two simple screws and the entire assembly lifted out. Open doors and covers and remove the toner cartridge. A secondary error indication can be obtained by pressing an releasing a button.

Press Select to continue. Cartridge Error Print cartridges are inserted in the wrong carrier. Roller is approximately 2" in circumference print defects with this repetitive spacing can be caused by transfer roller problems, on a standard 11" page defect would repeat five times. Check the wiring harness cable. I truly appreciate it.

Error 922 Fuser failed to reach standby temperature. Ensure the transparent tape is removed from both cartridges. Press Select. Use a memory card with images stored on it.

In Photo mode, image selected is larger than the selected blank paper size. Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 924 924 Fuser Error - Open circuit detected in thermistor circuit. Replace Printhead Pricing Error 935 Printhead Error - May have sub-codes. Consider purchasing a larger hard disk drive.

eCommerce Solution : k-eCommerce 3567 Benton Street, Suite 243 Santa Clara, CA 95051 800.360.1337 408.745.9800 Order Desk: 8 AM to 5 PM Home Contact Us About Us Terms of Sale Feedback