Lexmark Error Code 982.04
Reseat all of the paper feeders and trays on the printer. 0 Message Author Closing Comment by:answersanyone2010-10-18 Thanks! Check Toner Sensor Check Cable Check System Board Check developer drive for worn, loose or broken parts. Replace the system card assembly. Thanks The complete illustrated instructions for usingthe handset with the base are at this manualpage: http://bit.ly/2cwzrl1 (continued on thenext page).... http://support.lexmark.com/index?page=content&productCode=&segment=SUPPORT&userlocale=EN_US&id=SO3660
Thanks. I will have purchasing call in an order. http://www.marketpoint.com/article.cfm?id=100 If problem persists, contact the manufacturer. Thanks, Joe Posted on Jun 30, 2009 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Manolito Mendoza 236 Answers SOURCE:
Reseat the printer on top of the duplex option, if one is installed. Verify latch relay is operating - slowly close door and listen for interlock switch 3. Monkey "Understanding explains better..." Posted on Jan 21, 2011 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct.
Also, if the accumulated sheets are removed, the portion of the job printed after the jam will not be stapled. Replacement of the thermistor is not a cost effective repair, replace fuser assembly. Post a new question here... http://support.lexmark.com/index?page=content&id=SO4124 It can also be the LVPS (low voltage power supply) or a fuse in the power supply on some models.
Additional info on X and XX codes available by email. Error 59 Duplex Cover Open Top cover of duplex unit is sensed open. Note: This error indicates the printer was able to read the cartridge ID, but the ID did not pass the verification test. Thank you and your firm again, you were terrific.
Replace fuser assembly Replace Fuser Lexmark Fuser Error 145.XX (C520X/530X) Motor bump aligner service check 1. Check connecting cables for continuity. Mirror motor unable to reach operational speed, various other component level failures indicated by 935.XX Check cables, look for chafing or damage to ribbon cable at sharp bends around rear Error 30 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed properly and that it is detected by the ramp on
It may need to be replaced. have a peek at these guys Lexmark Recalls Find comprehensive Lexmark recall information updated hourly on RecallOwl.com. Error 24X Paper Jam - Check Tray "X" Primary: Paper is jammed around Tray X (X=tray 1 thru 5). The pin should enter the tower on the HVPS and depress the cover switch.
Power printer off one to two minutes. Sep 30, 2016 | Lexmark OfficeEdge Pro 5500 Inkjet... user-manual-Z640... http://jvmwriter.org/lexmark-error/lexmark-error-code-929-00.html http://www.officedepot.com/a/products/430730/Lexmark-85-Envelope-Feeder-For-T640/ Feb 28, 2011 | Lexmark T640 Laser Printer 1 Answer I HAVE GOT AN ERROR 900.00 SERVICE ON MY LEXMARK T640 PRINTER.
Lexmark Z640 InkJet... Check the toner metering cam on back of suspect cartridge. Go to "System card assembly removal (T650, T652, T654, T656)" on page 4-76. 1.
Replace the assys in the following order 1.
Check for 24V at red wire on interlock switch with door closed 4. Odin on 9/25 at 12:01PM | Uniden Can I Connect An Ipad Through The Ipod Connection Hi! Sign up! with 2000-sheet feeder option.
email with model, primary and secondary pattern for troubleshooting info. Please enter a valid email address. Controller Board 2. http://jvmwriter.org/lexmark-error/lexmark-error-code-57-3.html Go to "System card assembly removal (T650, T652, T654, T656)" on page 4-76.
Check fan connector and cable for loose or damaged connection. Click the "downloads" tab to find the drivers (Mac? Vista? It may be necessary to remove the re drive assembly to observe the lamp cycling on and off.
Bad bottom trunk on the paper port. NOTE: This toroid was removed in later versions of the 2000-sheet feeder. Check all output option interface connections if problem remains. Monkey "Understanding explains better..." Jan 21, 2011 | Lexmark T640, T642, T644 250-Sheet Duplex... 1 Answer Minha Lexmark T640 estÃ¡ apresentando Service Fuser Error appears when the fuser does not warm
Manuals / Documents Download any of our Lexmark T644 manuals for free! Check AC power source for noise. See Network Wrap Tests on page 23. by unknown on Oct 15, 2007 at 2:45pm Add comment Please sign in to comment 0 Just had this error on a lexmark t522 T D.
I did try that once before asking this question but second attempt seemed to be the fix! Sign Up Login Add Question leopard_crazy asked Oct 1, 2007 at 12:33pm 0 Unknown Printer 982 Service Engine Comm. We have the following 11 documents available for the Lexmark T644: Service Manual SCS/TNe Emulation Userâ€™s Guide IPDS Emulation Userâ€™s Guide User's Guide IPDS Printer and Host Setup Guide Menus and The OS is XP.