Home > Konica Minolta > Konica Minolta Fuser Error

Konica Minolta Fuser Error

The Konica service rep in Anchorage, Alaska is rude and unhelpful, at best! The lines are not all the same length and do not seem to have a pattern to them and they sometimes wrap around or are affected by image on paper.Does anyone I cannot get into the reset menu because of the error. Fuser errors need the trouble reset procedure to clear it. http://jvmwriter.org/konica-minolta/konica-minolta-3100-fuser-error.html

HTH Reply With Quote 11-12-2012 #8 JustManuals View Profile View Forum Posts Field Supervisor 10,000+ Posts Join Date Jan 2006 Location Las Vegas, NV Posts 10,067 Post Thanks / Like Thanks You should be able to find a 2400W real cheap. Pull the plate in the direction the springs allow it to go about a half inch then allow it to snap back into place. Any ideas will be greatly appreciated, TY. http://www.copytechnet.com/forums/konica-minolta/71423-bizhub-c650-fuser-error-reset-procedure.html

Help Me, please!!! Tell us some more! It says it’s Paused. Even the test page from the rom comes out the same.

Pushing down on the paper tray seems to have no effect.I gather that the design here is a little different, there is a solenoid or relay that activates paper pickup mode, Please help anyone! I know the rollers are ok because it works well if I have a bigger stack. Dec 17, 2008 | Minolta EP1030/1030F CS/PRO Copier 2 Answers Hp 4250 paper jam erro Is it a new or refurbished fuser?

black ink level-10\% cyan ink level-8\% magenta ink level-52\% yellow ink level-22\% if i take out magenta catridge and shake well and insert again,red color will come excessively but for a These levers reduce fuser pressure, and if theyare in the up position (i.e. This has fixed two printers so far that I have been sent to repair. http://www.fixya.com/support/t22152499-fuser_error_0500 I followed the instructions posted by "Soul Visitor" ...

any help would be greatly appreciated.sheine0127 by sheine0127 on Nov 16, 2009 at 6:48pm Add comment Please sign in to comment 1 PROBLEM: Text prints much lower than the set margins. Here it says "Press in the toner carousel latch" but has no further information for where to find this latch; and there is no diagram with a label saying "caousel latch". Hope it helps! Do you know the maximum size drive that can be installed?

by Anonymous on May 21, 2007 at 1:19pm Add comment Please sign in to comment 0 albengyYou answered your own question I believe. http://www.fixyourownprinter.com/posts/74287 Here is what I found from the official procedure. Privacy Policy Terms of Use Sign Up Login Add Question unknown asked Feb 22, 2011 at 7:57pm 0 Unknown Printer Konica Minolta 1690MF Non-existant fuser jam It keeps telling me there Join the revolution Become an Online Investor Today No minimum to start...

i.e., I found the "Trouble Reset Switch" (not shown in the user manual) by opening the upper back panel and pressing the small black button in the lower right hand corner navigate here I am so frustrated. I looked and the toner is not turning. The document is an ID CS3 doc and I am trying to print 100 copies, collated.

by Anonymous on Aug 21, 2007 at 2:33pm Add comment Please sign in to comment Duh, did you ever think to read the thread? Could anyone provide a diagram or instructions on how to reattach the spring? The time now is 04:13 AM. Check This Out Sometimes it also fails to pick paper when only a small amount of paper in tray too, even though the tray is lifted.

I would clean the small gold pads with an eraser as recommended, but the problem would resurface all too soon. It leaves me to beleive it is the scanner within the printer causeing this issue. I'd hate to think the waste toner filled up and shut down the printer, forcing me to buy a new Drum Cartridge (presently it reports 40\% life remaining for the Drum

by Growls on Apr 13, 2009 at 6:27am Add comment Please sign in to comment 1 I have a magicolor 2550 with a service call 16 error.What does this mean.

It is showing a media Jam at the transfer roller. You can use a paper clip to pull out, but probably not a permanent solution. Reply With Quote 11-11-2012 #2 habik View Profile View Forum Posts Private Message Field Supervisor 1,000+ Posts Join Date Apr 2010 Posts 1,639 Post Thanks / Like Thanks (Given) 200 Thanks solutionenterprises 223 προβολές 7:33 Top margin off Konica-Minolta MC-XXXX-W-TEST2 Solve this problem yourself!

solutionenterprises 4.140 προβολές 1:15 Bizhub network setup, scan to email, scan to file - Διάρκεια: 29:51. I tried reinstalling the toner cartridges but this was only a temporary fix. Does anyone out there have an idea? this contact form Luca Staf 11.303 προβολές 8:14 Imaging Unit Reset for Konica Minolta Bizhub C203 / C253 / C353 - Διάρκεια: 4:06.

I shut if off, restarted the printer and tried again - same thing. Hi All. It has about 65000 images printed. end of life message has now disappeared.If you have been using the drum for a while and the waste is getting full, empty out the grey waste toner before replacing (see

or it's affiliates. Is there any way to reset the memory card. The left one should have a plastic 'pin' and the right should have a groove/track. PS I have service manual, but do not see anything in troubleshooting section pertaining to this problem.Sincerely, Magna by unknown on Oct 23, 2007 at 7:08pm Add comment Please sign in

Get up to $600 for opening a new account... Thanks by unknown on Sep 7, 2006 at 12:11pm Add comment Please sign in to comment 0 Hello,Where do you get your toners from? I'm at my wits end here! go to setting that allows you to change you setting to continue printing when toner empty light comes on ! - realsteel 3 Hi all,I have a KONICA MINOLTA magicolor 2400W

When my company upgraded to this version of OS, we found out that KM does not have a driver for the OS and the BizHub. Konica Minolta has just changed service companies and have moved from Getronics to Laserfast. After like 3 hard reboots we can get it to work or we have to pull out the cartridges and put them in a warmer room and then come back later yes=get a new one, also try to reseat the transfer belt assychas williams: don't buy it off ebay, remove the fuse from your current one, replace it wil a piece of

solutionenterprises 11.221 προβολές 2:20 konica 1690 parts Knowledge mpeg4 - Διάρκεια: 11:45. The top one is very high (easy to miss), but the lower one was my problem, with it sticking behind the hole. by Scytex on Feb 23, 2011 at 4:53pm Add comment Please sign in to comment 0 Where is the exit switch arm? First is the failure of the 8.5x11 paper to fully eject at the top with the error message of a paper jam.