Home > Hp Laserjet > Laserjet 5 Error Paper Jam

Laserjet 5 Error Paper Jam

Contents

Usually, this occurs in the tray, but now it is in the compartment where I have to remove the ink cartrage to get the jam out. Any help would be great. If any torn pieces of paper remain inside the printer, more paper jams might occur. After being in storage last winter, it will feed paper to the internal (below the toner cartridge) roller where it stops. http://jvmwriter.org/hp-laserjet/laserjet-51-1-error.html

If you people won't cooperate and answer my questions, I'm not helping you. I'm not sure what that sensor does, but somehow it taping it into position has fixed my problem. Make sure you have it unplugged though and wait awhile becuase its extremely hot. Whatever the paper was hanging on, the tape smoothed out and it passed over it.

Hp Laserjet 4 Pickup Roller

If you accept, open it up flat, put it in a large plastic bag and a box with lots of squashed newspapers or peanuts would be better. The printer is ready to use. Wash it in some water and dry it off. It does not pick up the paper, just says it's jammed.

Thanks by unknown on Dec 22, 2013 at 12:27am Add comment Please sign in to comment 0 Like I mentioned in an earlier post, you have to watch the pickup roller. Two screws on bottom metal just inside back door and the fuser pulls out and you can check that, also the gear that breaks can be checked with the fuser removed. Thankx by Anonymous on Jan 12, 2006 at 11:19am Add comment Please sign in to comment 0 That is because the back door had to be removed to install the duplex Hp Laserjet 4 Fuser by moe on Jan 12, 2006 at 9:19am Add comment Please sign in to comment Yup - I sure did, but I can't find the location of the paper sensors or

RESTORING FACTORY SETTINGS This message is displayed during a cold reset. 13 Paper Jam WARNING: To avoid risk of injuries or electric shock, you must disconnect the power cord before you reach inside the printer. PROCESSING JOB This message is displayed when the printer is processing a print job.

I have seen a few go missing, but when that happens, the page is blank.

REQUESTED LANGUAGE NOT AVAILABLE This warning idicates that a print job requested a personality that did not exist in the printer. Hp Laserjet 5m If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message. by nivek on May 15, 2009 at 10:04am Add comment Please sign in to comment 0 I'm confused about that paper sensor on the left side. The second sheet of paper has moved past the transfer roller and is now just trailing the first sheet of paper, nearly touching and sometimes cocked a bit.

13 Paper Jam

Jam occurs with both tray and manual feed. Parallel configuration: check for loose cable; use a high-quality cable - some cables may be missing pin connections. Hp Laserjet 4 Pickup Roller Examine the paper pickup and feed rollers for wear. Rg5-0886 Service Messages Message Description Recommended Action 50 FUSER ERROR, CYCLE POWER The printer identified an internal service error.

It stops in an area of the fingers before making the bend into the upper roller and before any jamming or wrinkling of the paper. weblink Showing results for  Search instead for  Do you mean  or Post new question Question HP LaserJet P3015 phantom paper jam? Once the printed sheet is removed, the top of the printed sheet is curled up from travel through the rollers – sheet is not accordion shaped. Jam in cartridge area Jam in output bin Jam in duplex area Jam in the document feeder Tips for preventing paper jams Review these tips to help prevent recurring paper jams. Hp Laserjet 4p Paper Jam

If you switch the printer off, then on, you may lose settings (to check settings, print a self test). Engineering excellence and quality products....another has been company run into the ground by pointy-haired 'management'...... not sure where you live but there will be a supplier in your country. http://jvmwriter.org/hp-laserjet/laserjet-5l-error.html If the printer picks two sheets of paper at once. 4.

there seems to be an issue that intermittently keeps the pinch rollers from activating at the proper time. Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew Go to Contact HP Support to review available service options.

WARNING: To avoid risk of injuries or electric shock, you must disconnect the power cord before you reach inside the printer.

i got the first paper jam out.. If it occured while paper was present, you got the other codes.The sensor test mode under diagnostics tab. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎10-28-2013 08:27 AM Sigh, I feel your pain. Remove the page from the output bin and press [Go].

If you completed all the preceding steps and your product still has an issue, you might need further assistance from HP. Turn the duplex option off in the printer software. I also note that the right hand side of my legal and letter sized papers are coming out with little creases on them. his comment is here Thank you.

Inspect the front half of the paper path for another piece of paper stuck elsewhere in the printer. Getting a repairman to do the work could end up being costly so if it is still under warranty, phone them up, tell them what it is and hopefully they will I did, however, come here to give a valid solution that may help most of you people out due to the fact that I too, recently had the same issue. No action required.

If the error reappears, call your dealer or HP service representative. 79 SERVICE (XXXX) The firmware has detected an unrecoverable error. If not open the rear door and check there its probably stuck in the fuser unit. Wait at least 60 seconds. I open the back door and I see the paper exiting the fuser, running up betweeen the rollers and the top of the paper stops just on the front side of

If it is a soldering issue then there would be other areas that would be affected as it is the MB we are talking about.I own and run a computer business