Home > Hp Laserjet > Laserjet 4300 Error Codes

Laserjet 4300 Error Codes

Contents

The screen stays at New Maintance Kit. Push the fuser firmly--listen for the sound of both blue levers clicking into place. A:  It is not uncommon for hp laserjet 4300 printers to loose their network connectivity especially since they were outfitted with the 615 network cards.  Try printing the network configuration settings.  What did fix it was replacing the DC controller. http://jvmwriter.org/hp-laserjet/laserjet-4300-service-error.html

Turning the printer off and then on can clear some of these messages. Print a menu map by pressing the Check button and then the Down Arrow to Information. All images and logos used with permission from the respective owners. If the error persists, replace the HP Jetdirect card (EIO card). http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422

Hp Laserjet 4250 Error Codes

X Description 1- Low fuser temperature 2- Fuser warm-up service 3- Fuser over temperature 4- Line voltage problem 5- Incorrect fuser is installed 6- Open fuser circuit Action Turn the printer Turn the printer off and then on. alternates with 64 PRINTER ERROR To continue turn off then on Description A temporary printing error occurred in the scan buffer.

Loading Tray 2 or an optional 500-sheet tray Remove the tray from the printer. Error 10.32.00 Unauthorized Supply Alternates with for help press "?" - A new non-HP supply has been installed this message continues until you press the check button or install an HP If the above action does not solve the issue, contact HP or authorized service provider. Hp Laserjet 4250n 49.4c02 Service Error alternates with 41.X PRINTER ERROR To continue press (Select) Description A temporary printer error has occurred.

The chip may be missing or defective or contain incorrect information. Hp Laserjet 4200 Error Codes alternates with 52.XY PRINTER ERROR To continue turn off then on Description A temporary printer error has occurred. Set the output bin cover aside. Close the door.

Laser Jet printer 4300 ONLY error 57.4 replace the fan 1 LaserJet printer error 57.7 duplex fan failure replace the duplexer fan LaserJet printer error 58.2 air-temperature sensor, LaserJet printer error 13.98 Paper Jam Can also be formatter PCA. If a duplexer is installed, remove it from the back of the printer. top 66.12.XX OUTPUT DEVICE FAILURE For help press?

Hp Laserjet 4200 Error Codes

If jammed, paper is present, remove it. https://www.orionmarket.com/product_error_page/HP/HP-4300/ Figure 13: Opening the top cover and removing the print cartridge Use the green handle to lift the paper-access plate. Hp Laserjet 4250 Error Codes How about the I/O port - damaged, seated properly, pins not bent? 4+/5P/5 The computer and printer aren't talking because of improper signal protocols. Hp Laserjet 4200 Cartridge Installed Message CLEARABLE WARNINGS has two settings, JOB (the default) and ON.

This causes static electricity, which can cause paper jams. weblink The display should show skip disk load. If the above action does not solve the issue, contact HP or authorized service provider. CAUTION: Do not fan the paper. Hp Laserjet 4200 And 4300 Series Printers Drivers

Access deniedMENUS LOCKED 13.01.00. Figure 45: Disconnecting cables Grasp the cover on the right side of the printer and pull it firmly toward the rear of the printer until it stops. I have removed a page that was jammed in the printer but now the paper jam error will not clear. navigate here If loose toner falls into the printer, it might cause temporary problems with print quality.

They change as the state of the printer changes. Hp Laserjet Error Codes The outside plastic and metal frame look the same, but the inner wiring is different. Fans will go into high speed operation during the print cycle.

Back back to top How did we do?

Firmware Update - The configuration page lists the firmware version of the product. Laser printers are page printers and require the entire page to be processed before beginning to print. Wait for RESET MAINTENANCE COUNT to be displayed and then release both keys. NOTE: Some versions of the 4000, 4050, 4100, and 5000 will NOT have their maintenance count reset 82.0180 Eio 2 Error WARNING: The fuser is very hot so please be careful.

XX Description 00 memory error on the cartridge or 01 memory device not found 10.00.00 Black print cartridge 10.00.01 Cyan print cartridge 10.00.02 Magenta print cartridge 10.00.03 Yellow print cartridge Supplies X represents the fan motor number associated with the error. If the display panel on your HP LaserJet printer reads "PERFORM PRINTER MAINTENANCE" your HP LaserJet printer needs a maintenance kit, which includes a fuser unit and separation rollers. his comment is here If the above action does not solve the issue, contact HP or an authorized service provider.

Turn the printer off/on to attempt to clear or reset the message. How to Reset the maintenance count on HP LaserJet 4100mfp/4101mfp, 4200/4300, 4250/4350 and HP 9000/9040 and 9050! 1. top 13.98.00 OPEN INPUT TRAYS THEN OPEN AND CLOSE TOP COVER Description The rear output bin was opened when the printer was attempting to send a page to the duplexer, a These settings set the amount of time that a clearable warning is shown on the printer control panel display.

top 13.13.00 JAM INSIDE DUPLEXER Description A page is jammed inside the duplexer. If the above action does not solve the issue, contact HP, or contact an authorized service provider. Action Turn the printer power off and then turn the printer power on. The EIO accessory might be defective. 7 = EIO slot 2 - The EIO accessory detected an error.

Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps. If the toner gets on clothing, wipe it off with a dry cloth and wash the clothing in cold water. TRAY XX CONTAINSUNKNOWN MEDIA 68.X PERMANENTSTORAGE FULL TRAY XX EMPTY{TYPE} {SIZE}alternates withReadyFor help press "CheckMark Icon" 68.X PERMANENTSTORAGE WRITE FAIL TRAY XX OPENFor help press ?alternates withReadyFor menus press "CheckMark Icon" Make sure that the accessory is properly seated on and connected to the printer, without any gaps between the printer and the accessory.

Verify that the tabs aren't damaged and that the tray switches located in the printer are not damaged. If a message persists after performing all of the recommended actions, contact an HP-authorized service or support provider.