Home > Hp Laserjet > Laserjet 4250 69.00 Error

Laserjet 4250 69.00 Error

Contents

They offer information about normal printer operation and no interaction is required to clear them. Figure 21: Removing the paper If the paper has torn, or you still cannot remove it, click here for more information about clearing jams from the fuser area Reinstall the fuser If the message persists, contact HP Customer Support. Action Press the (Select) button to continue. Check This Out

This document explains the message types, it lists and explains the numbered error messages, and provides recommended actions for resolving problems. and may not be used without advance written permission of PrinterTechs.com, Inc. On the right side of the stapler/stacker, turn the stapler unit toward the front of the printer until the unit clicks into the open position. If the error does not clear, turn the printer power off and then turn the printer power on. http://printerrepairsupport.com/69-x-printer-error-hp-4240-4250-4350/

Hp Laserjet 4250 Error Codes

Replace a DIMM or EIO device if you determine that it causes the error. 11. CAUTION: Ensure that all jammed paper is removed before closing the cover or tray. If loose toner falls into the printer, it might cause temporary problems with print quality. Duplex slide adjust has failed. 3.

top CLEARABLE WARNINGS and AUTO CONTINUE settings Some printer messages are affected by the printer CLEARABLE WARNINGS and AUTO CONTINUE settings. Figure 28: Closing the rear door If the error persists replace the stapler/stacker or stacker. If you are printing from any tray except Tray 1, verify that the three paper size adjustments on the tray have been made correctly. Hp Laserjet 4200 And 4300 Series Printers Drivers All rights reserved.

If the incorrect fuser goes in, you can get a 50.5 error (or a 13.20 error in some cases) when you power on the printer. Turn the printer off, and then turn the printer on. 3. Thank you! Temporary error.

Replace a DIMM or EIO device if it is the one that has caused the error. 13.98 Paper Jam If the message appears only with a certain software program or print job, contact the software vendor for assistance. If the issue reoccurs, try installing a known good duplexer from another compatible unit, if possible. Turn the printer off, and then turn the printer on. 2.

Hp Laserjet 4200 Error Codes

Turn the printer off. 6. https://www.laserzone123.com/4250-error-codes.html alternates with 51.XY PRINTER ERROR To continue turn off then on Description A temporary printer error has occurred. Hp Laserjet 4250 Error Codes Replace the formatter. 79 & 80 errors - general info. Hp Laserjet 4200 Cartridge Installed Message Remove all paper from the output bin.

If the message persists, contact HP Customer Support. his comment is here Figure 45: Disconnecting cables Grasp the cover on the right side of the printer and pull it firmly toward the rear of the printer until it stops. The duplex printing unit is not functioning. 2. Figure 29: Removing duplexer Remove any paper on top of Tray 2. (You might need to reach inside the printer.) Figure 30: Removing paper from Tray 2 Slowly pull any paper Hp Laserjet 4250n 49.4c02 Service Error

Some non-HP parallel cables might be missing pin connections or might otherwise not conform to the IEEE-1284 specification. Action Turn the printer power off and unplug the power cord from the printer. Figure 6: Replacing the entrance cover and closing Tray 1 Reinstall the print cartridge and close the top cover. http://jvmwriter.org/hp-laserjet/laserjet-5l-error.html Push the fuser firmly--listen for the sound of both blue levers clicking into place.

Reseat duplexer.3. Hp Laserjet Error Codes Try printing a job from a different software program. Scroll to the System Setup submenu, and then scroll to either CLEARABLE WARNINGS or AUTO CONTINUE.

This will clean up the permanent storage by removing old areas that are not being used. 69.X PRINTER ERROR alternates with CYCLE POWER TO CONTINUE A temporary printing error occurred.

Figure 18: Replacing the entrance cover and closing Tray 1 Reinstall the print cartridge and close the top cover. If the problem persists, turn the printer power off and then turn the printer power on. Action Press the (Select) button to resume printing. 60.02 Error Figure 51: Closing DIMM access door Set the bottom of the cover onto the printer.

Plug the printer into a wall outlet and see if this resolves the problem. World of The Internet HOME Youtube Download App Android Contact Us skip to main | skip to sidebar Hp Error Code 69, Service Errors 69 Printer Repair Message Written By Sudiyana Temporary duplexer error. 2. http://jvmwriter.org/hp-laserjet/laserjet-51-1-error.html Figure 36: Opening the rear output bin Remove the rear output bin and extension by bending the middle of the bin down and releasing the two hinge pins.

The best way to determine which fuser you have is to pull the fuser out of your printer and check the barcode label on the fuser. X Description 2- air-temperature sensor 3- DC controller 4- power supply Action Turn the printer off and then on. Turn the printer power off, reseat the EIO accessory in slot [X], and then turn the printer power on. top Provide feedback Please rate the information on this page to help us improve our content.

These messages typically alternate with the “Ready” or “Status” messages and remain displayed until the (Select) is pressed. CAUTION: To prevent damage to the print cartridge, do not expose it to light for more than a few minutes. Figure 13: Opening the top cover and removing the print cartridge Use the green handle to lift the paper-access plate. If a duplexer is installed, remove it from the back of the printer.

CAUTION: Do not fan the paper.