Home > Hp Laserjet > Laserjet 4 50 Service Error

Laserjet 4 50 Service Error

Contents

Press Continue to print the transferred data, then simplify your print job or install additional memory. 21 PRINT OVERRUN The data (rules, dens text, raster or vector graphics) sent to the This is one way to fix your problem. W5 JOB 300/LTR The job was printed at 300DPI with page protection set to letter. There is lots more, you need the service manual to know how to disassemble it. http://jvmwriter.org/hp-laserjet/laserjet-49-service-error.html

Basic Parts that Make up a LaserJet 4 Fuser: Upper and Lower Fuser Rollers.Various Gearsm diffrent sizes too.The fuser chassis, and supports.Thermal Sensors and wiring.Bushings for upper rollers.Fuser Heater. For those who have a similar problem, here is the deal. Could also be a failure of thepower supply.a.. Measure between the two heavy gauge pins on the fuser assembly connector. http://www.fixyourownprinter.com/posts/21552

Hp Laserjet 4 Fuser

No action required. 07 Reset Follows a control panel Reset selection. Optional Fonts Cartridge Fonts Font Test To check fonts available in printer, take printer off-line and press the [Menu] button repeatedly until the TEST MENU appears. Failure to wait the full 10 minutes before turning the printer ON results in a continuation of the error message and the shutting off of the fuser lamp current during this The fuser below has no tabs installed.

If TONER LOW=ON this message will remain in the display until the tone cartridge is replaced. XX Load [media size] The printer received a request for a paper or envelope size not available in the printer. You may have tried to transfer too many macros or soft fonts, or graphics that were too complex. 50 Fuser Error Hp Laserjet 3055 Support for our customers is always available via email and live chat.

I truly appreciate it. Hp Laserjet 4 Fuser Kit Bad AC Power Supply Bad fuser: Check heater lamp, thermistor, thermostat and replace whichever is bad. Rogers rocks cherrs 7-29 If a 50 SERVICE error message is displayed, turn the printer OFF for at least 10 minutes. http://www.all-laser.com/a50service/ to clear the display, remove the card and switch the printer OFF and then ON.

Remove the plastic side cover and whatever sheet metal to get at the front end of the supply and check for 110VAC at J102. Hp Laserjet 4p Fuser Assembly Replace the SIMM that caused the error. In some cases this error can also be caused by a defective power supply or faulty DC controller board, but check the fuser first. See the user's manual for the MIO card.

Hp Laserjet 4 Fuser Kit

spelling Fortune Cookie says: Fortune not Found: Abort, Retry, Ignore? http://www.bleepingcomputer.com/forums/t/483223/hp-laserjet-5n-fuser-error-message/ Add to Want to watch this again later? Hp Laserjet 4 Fuser I tested the fuser based on this link http://www.fixyourownprinter.com/reference/guides/fuser/ex. Hp Laserjet 4 Fuser Replacement Your decision.

So I didn't have to replace the lower voltage power and get the printer fixed. his comment is here I am new to this and do not want to screw this up. But I do appreciate your help and concern. Is there any way you can get these fusers into another LJ 4 to test them? 50 Fuser Error Hp Laserjet 3050

Serial configuration: wrong pacing option may have been selected. (If you are using an RS-232C serial connection, the HP LaserJet printer uses XON/XOFF and DTR/DSR signal protocols rather than ETX/ACK protocol.) If necessary, press On Line. 02 Warming Up The printer is warming up and is not ready to accept data. As a guest, you can browse and view the various discussions in the forums, but can not create a new topic or reply to an existing one unless you are logged http://jvmwriter.org/hp-laserjet/laserjet-4300-service-error.html Can I join the club? :D If anyone has a pdf manual for the 4 Plus could they PLEASE send me a copy??

Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. ROM size 6: Invalid SIMM speed 7: SIMM reporting information incorrectly 8: SIMM RAM parity error 9: SIMM ROM needs to be mapped to an unsupported address 10: SIMM address conflict Turn off ads with YouTube Red.

I have seen working LJ4's at the surplus places for $20.

Now, for the 50 Service Error: This error can mean 2 things: 1. No action required. 06 Printing Rest Printing a self test. Press On Line to return to 00 Ready Use your software application to select the appropriate envelope size. Have you ever heard of this website: www.google.com It's a great site, you can find a lot of info about almost everything, for example this: h**p://www.fixyourownprinter.com/kkl0.html and this: h**p://forums1.itrc.hp.com/service/forums/questionanswer.do?admit=716493758+1100665226872+28 353475&threadId=731499 Or

You can Self maintain your printer and save. Jump to content Sign In Create Account Search Advanced Search section: This topic Forums Members Help Files Calendar View New Content Forum Rules BleepingComputer.com Forums Members Tutorials Startup List Ensure that the paper size knob is set for the installed paper. http://jvmwriter.org/hp-laserjet/laserjet-51-1-error.html Sign in to make your opinion count.

You can remove the fuser assembly from the printer and measure the resistance of the lamp/thermal fuse circuit - it should be less than five ohms. If this occurs, load the requested media in the MP tray; the printer will return on line. Press On Line of Continue to stop the test. That's it.

Perfect for Internet, Not for heavy usage or gaming however. Thank you and your firm again, you were terrific. Perfect for Internet, Not for heavy usage or gaming however. This feature is not available right now.

HP IIP/IIP+/IIIP most likely cause is burned out quartz lamp.