Home > Hp Laserjet > Laser Jet 4200 Printer Error Messages

Laser Jet 4200 Printer Error Messages

Contents

Refer to the following instructions for additional information about adding more memory: NOTE: If you have not already done so, print a Configuration page to find out how much memory is Figure 57: Turning the knob Load paper with the front side facing down and the top edge toward the front of the tray. HP LJ 4200 50.6 Error open fuse circuit 51.XY printer error 51.1, 51.2 printer errors A temporary beam detect error has occurred in HP 4200. 1. If the error persists, replace the stapler unit. Check This Out

If a duplexer is installed, remove it from the back of the printer. Learn more You're viewing YouTube in Greek. Figure 61: Sealing tab on end of print cartridge 1 - Sealing tab bent and removed from end of print cartridge CAUTION: Avoid touching any black toner on the tape. Open the top cover and remove the print cartridge.

Hp Laserjet 4250 Error Codes

Remove the print cartridge and check the paper path for paper. Plug the printer into a wall outlet and see if this resolves the problem. Make sure that the accessory is properly seated on and connected to the printer, without any gaps between the printer and the accessory. Interval 200,000 pgs 200,000 pgs Service PIN 11420002 11420002 HP LaserJet/Laser Printer Repair Parts Fuser, 110v RM1-0013 (4200) In Stock Maintenance Kit, 110v Q2429-67905 (4200) In Stock

If the message persists, contact HP Customer Support. Warranty status:Unspecified Check warranty status Enter product serial number The serial number you entered,, matches a different product than the current product. We repair LaserJet t 4200 printer failure with firmware error code 49.24.02, Error 49.C02 and 49.C06 error codes by upgrading the firmware. Hp Laserjet 4250n 49.4c02 Service Error Remove the spring, fold up one of the coils where the spring broke and reinstall.If the spring is attached, then either try a new tray (500 sheet tray part # RM1-1088]

Replace any defective print cartridge. top 13.XX.YY JAM Description A paper jam exists in the paper path. By adding a small spacer to the back right side of the paper tray you can make the tray more snug in the printer eliminating the noise and error. this page Figure 11: Sliding tray back into the printer Open and close the top cover to clear the jam message.

If a jam message persists, it is possible that paper is still jammed in the printer. 13.98 Paper Jam HP LJ 4200 printer with 13.12.00 error message indicates that there is paper jammed in the rear door. The monthly duty cycle is rated at 150,000 pages. Release the checkmark (Select) button. 6.

Hp Laserjet 4200 Error Codes

Ensure that tray is not over-filled or damaged. Figure 21: Removing the paper If the paper has torn, or you still cannot remove it, click here for more information about clearing jams from the fuser area Reinstall the fuser Hp Laserjet 4250 Error Codes A stacker or stapler/stacker error has occurred. Hp Laserjet 4200 Cartridge Installed Message If the sealing tab cannot be removed, insert a new print cartridge and return the faulty print cartridge to receive a replacement.

Figure 18: Replacing the entrance cover and closing Tray 1 Reinstall the print cartridge and close the top cover. NOTE: 13.20 is a false paper jam error and there is a paper jammed behind the tray 1 assembly 13.06/13.12 Jams/Jam inside rear door There is a paper jam inside or Turn the power off. Turn the printer power off. Hp Laserjet 4200 And 4300 Series Printers Drivers

Turn the printer off and then turn the printer power on. End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew ZealandÖsterreichParaguayPerúPolskaPortugalPuerto RicoSchweizSouth AfricaSuisseTürkiyeUnited KingdomUnited StatesUruguayVenezuelaΕλλάδαРоссия中国台灣日本香港대한민국End of No more paper jams! this contact form Lift the optional duplexer up and then pull it out to remove it.

Install the replacement fuser by inserting it and aligning the left side first. Hp Laserjet 4250 Error 13.01.00 Jam In Tray 2 Next, lower the rear output bin cover as shown below. The dual inline memory module (DIMM) that caused the error will not be used.

Figure 58: Loading paper Make sure that the stack is flat at all four corners and that the top of the stack is below the maximum-height indicators.

The stapler/stacker LED blinks in amber. This high performance HP Laser 4200 printer was designed to quickly and efficiently print large size documents with print engine speeds of up to 35 pages per minute. Recent products: HP LaserJet 4200 Printer series Troubleshoot a problem Help Other Knowledge Base options Search HP Support Center Most viewed solutions Advisories, bulletins & notices Manuals Setup & install Learn 13.20.00 Jam Inside Rear Door Click here for instructions on how to print a Configuration page.

top 64 PRINTER ERROR For help press? Please try again later. and may not be used without advance written permission of PrinterTechs.com, Inc. If you have an active support agreement or HP Care Pack, you can link them to your profile to ensure access to all services.

If tape has been removed, replace the toner cartridge. If the incorrect fuser goes in, you can get a 50.5 error (or a 13.20 error in some cases) when you power on the printer. Pressing the Select (check) button should clear the message. Figure 46: Pulling the cover on the right side of the printer Remove the cover from the printer.

Make sure the bottom tab on the cover fits into the corresponding slot in the printer. Make sure it locks into place. Scroll to the System Setup submenu, and then scroll to either CLEARABLE WARNINGS or AUTO CONTINUE.