Home > Error Codes > Lexmark Optra T620 Error Codes

Lexmark Optra T620 Error Codes

Contents

The fuser can usually be removed with two simple screws and the entire assembly lifted out. Error 80 Printer has reached 200,000-300,000* prints without maintenance count reset. Error 80 Network Card Codes These user codes are documented in various network card user manuals. Replace Printhead Pricing Error 934 Printhhead Error - Lost Lock condition Indicates a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system check over here

It may be necessary to remove the re drive assembly to observe the lamp cycling on and off. Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. There was an error with the application. Fuser Pricing How did we do? http://www.manualslib.com/manual/482154/Lexmark-T620.html?page=30

Lexmark Error Codes

Replace the system board. The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure. br Lamentamos o inconveniente. Check for 24V at red wire on interlock switch with door closed 4.

I am new to this and do not want to screw this up. Secondary: When this message is displayed, do not remove accumulated sheets during the jam clearance procedure as the printer will not reprint the removed sheets. Check the wiring harness cable. Reconnect.

No inkjet error codes available Error Code Error Message Solutions ERROR 20 ERROR 200 Input Paper Sensor was not triggered - Paper may be jammed at the sensor. Lexmark Support Power printer off one to two minutes. If the test fails, the disk is defective or the data on track1 is bad. Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed.

Verify correct cable connections from the Engine board to the HVPS. Remove jammed media Error 250 Paper Jam - Check MP Feeder Paper is jammed in the multipurpose feeder. Load correct size Error 28 Input sensor not made after pick attempt. Paper not being picked up check paper tray & pickup rollers Replace rollers if worn smooth or cracked ERROR 21 The exit sensor was not made in time after the input

Lexmark Support

See “Network Wrap Tests” on page 23. Discover More Mirror motor unable to reach operational speed, various other component level failures indicated by 935.XX Check cables, look for chafing or damage to ribbon cable at sharp bends around rear Lexmark Error Codes POR several times Check each board for secure ground. Replace the bump alignment motor Replace bump motor Replace interlock switch Replace System Card Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex

Replace fuser assembly Replace Fuser Lexmark Fuser Error 145.XX (C520X/530X) Motor bump aligner service check 1. check my blog Replace the assys in the following order 1. In general, fuser errors require replacement of the fuser as a cost effective repair. There was an error with the application.

ERROR 23 Jam at the duplex unit. Make sure there is no paper jammed in the printer. Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. this content Make sure the memory shown on the printout matches the installed memory.

Es gab einen Fehler bei der Anwendung. de Wir entschuldigen uns für die Unannehmlichkeiten. Error 82 Photo Developer Cartridge Exhausted The Photo Develper (OPC belt cartridge) has reached the end of it's life and must be replaced.

Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed.

Remove the duplex front cover to access the jam area. Error 930 The wrong printhead is installed. Any help here would be appreciated too. Intterconnect Board Error 940-943 Color Machines Toner Metering Cycle failure CMKY cartridge 940 = Cyan cartridge 941 = Magenta cartridge 942 = Yellow cartridge 943 = Black cartridge Toner metering cycle

If cables, connectors and connections are good replace assemblies listed. Error 122 Fuser Error - Problem in the fuser, not heating, heating to quickly or too hot. Check LVPS cable for continuity. have a peek at these guys Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers

If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is Error 38 38 Memory Full Memory used to store pages is full. Remove jammed media How did we do?

These errors indicate an unrecoverable engine software error. If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact. Error 26 Duplex unit is installed but paper tray is not sensed. Houve um erro com o aplicativo. 3567 Benton Street, Suite 243 Santa Clara, CA 95051 800.360.1337 408.745.9800 Order Desk: 8 AM to 5 PM Home Contact Us About Us Terms

Wayne Haub Kansas City Save time and money by servicing your own Lexmark printer Lexmark Laser Printer Error Codes Lexmark error codes may not apply equally to all models. de Wir entschuldigen uns für die Unannehmlichkeiten. Il ya eu une erreur à l'application. Try opening Tray X.

br Lamentamos o inconveniente. Install more memory Simplify print job Delete fonts, macros and other data stored in RAM Error 39 Page too complex to print.To verify that the printer recognizes all the installed memory, Perform fuser service check. es Lamentamos las molestias.

Hide thumbs Also See for T620 Setup manual - 38 pagesQuick reference - 2 pagesTroubleshooting - 1 page 1 2 3 4 5 6 7 8 9 10 11 Error Code 900 RIP Software 901 Engine Flash 902 General Engine Software 903 Paperport Link Driver Error 904 Interface Violation by the controller software 905 Interface Violation by Paperport Device 906 The transfer roller is included in the maintenance kit. Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 924 924 Fuser Error - Open circuit detected in thermistor circuit.

Error 54 Serial Error - Framing or parity error on serial.