Home > Error Codes > Lexmark Optra T614 Error Codes

Lexmark Optra T614 Error Codes

Contents

Replace printhead, system board or ribbon cable. the green belt often gets scored on the edge where the sensor is meant to pick up the homing position... - Anonymous 0 Worked like a charm on a T616. Error 47 47 Font Card Removed While Printing Printer needs data on removed card. Can be system board or printhead. check over here

by szyslak on Aug 18, 2005 at 2:02pm Add comment Please sign in to comment Press GO button to clear the 54 error - Anonymous 0 I have an Optra T614 Error 62 Disk Full Not enough disk space for data that has been requested to be written to disk. Up & going !! you will experiance paper jams more frequently,lockups after time spent idle.900 rip errors. http://support.lexmark.com/index?page=content&locale=en&productCode=OPTRA_T614&segment=SUPPORT&clearQuestion=Y&userlocale=EN_US&id=SO2001

Lexmark Error Codes

The main motor assembly may need to be replaced. Thank you and your firm again, you were terrific. In general, fuser errors require replacement of the fuser as a cost effective repair. by Anonymous on Apr 10, 2007 at 11:10am Add comment Please sign in to comment C510 931 error normally means a problem with the printhead...but C510 is a pretty cheap machine,

Be sure to follow all of the instructions. Thanks. Also, if the accumulated sheets are removed, the portion of the job printed after the jam will not be stapled. Lexmark Crc Failed Do Not Power Off All rights reserved.

Privacy Policy Terms of Use Sign Up Login Add Question unknown asked Feb 25, 2002 at 7:41pm 0 Lexmark Optra R Lexmark Optra T614 -900 Service RIP Software Hello, hope someone I had a similar (maybe the exact same) problem three or four years ago and was told that was what I needed to do. Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed. http://support.lexmark.com/index?pmv=print&page=content&locale=en&productCode=OPTRA_S_1625&segment=SUPPORT&userlocale=EN_US&id=SO1539 I've also read here that I may be able to send the printer new RIP software.

Error 32 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer. Lexmark Engine Error The first plan of action is to try the firmware reflash and a lot of the time this will solve the problem. Error 924 924 Fuser Error - Open circuit detected in thermistor circuit. Los Altos Hills, CA Thank you.

Lexmark Printer Error Messages

Controller Board 2. http://www.fixyourownprinter.com/posts/35604 email with model, primary and secondary pattern for troubleshooting info. Lexmark Error Codes Remove and reinstall print cartridge. Lexmark Invalid Engine Code Mode The Readme.1st filecontains directions for sending the file over through a parallel connection.

See “Network Wrap Tests” on page 23. check my blog You will need to download the appropriate file from the Lexmark FTP site (see detailed instructions below)andyou will also needa direct parallel connection from the printer to a DOS-based computer. (You Check fan connector and cable for loose or damaged connection. Send an Email Toll Free: 877-365-1903 About us Terms Contact us Help Login Brand : All brands HP Models Lexmark Models Xerox Models Model : Choose a brand Service Error 146.00 Dc Pick Motor

Check fan connector and cable for loose or damaged connection. Check the operation of the toner sensor. The fuser assembly is subject to mechanical wear and heat related degradation and is a scheduled replacement item in most machines at between 200K and 350K pages. http://jvmwriter.org/error-codes/lexmark-optra-t620-error-codes.html Observe the lamp through the left near side of the printer.

by aerolaser on Jan 26, 2009 at 12:21pm Add comment Please sign in to comment 0 The network card (separate or integrated) can sometimes cause these errors. Lexmark Dc Pick Motor Fuser errors can be from a cold fuser or an overheated fuser. The other major problems with the 612 614 and 616n printers is the network card failing giving a 54 std network software error.

Any help?

There are differences, for example the T614n is 41e (has built in Ethernet and Centronics parallel).Anyway, the Lexmark firmware compatibility guides you to the printer model. If an open circuit, replace the lamp or fuser. Error 920.X and 922.XX may display for a cold fuser. Lexmark Error Codes Problem Use caution when measuring AC voltages.

You’ll need to replace the High Voltage Power supply. POR several times Check each board for secure ground. Cycling the power was the only way for me to get rid of the error. have a peek at these guys Remove jammed media How did we do?

it Ci scusiamo per l'inconveniente. Error 62 Disk Full Not enough disk space for data that has been requested to be written to disk. Il ya eu une erreur à l'application. THANK YOU!!!!!!

So, how can I diagnose with some degree of certainty wether it is the RIP board, the engine Board, or the "System" board that needs to be replaced? Newer machines display a sub code to indicate which condition applies. Error 43 Font card format not supported by printer. Error 80 Network Card Codes These user codes are documented in various network card user manuals.

Error 7X Network Card Codes These user codes are documented in various network card user manuals. The pin should enter the tower on the HVPS and depress the cover switch. If the 902 error does return, please go through the checklist below. Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the down position if applicable to your machine.

Replace the assys in the following order 1.