Home > Error Codes > Lexmark Optra T610 Error Codes

Lexmark Optra T610 Error Codes

Contents

Error 925 Wrong fuser lamp installed. Remove and reinstall print cartridge. Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22. If one of these errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace weblink

Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex Unit. The transfer roller is included in the maintenance kit. Check the continuity of the fuser lamp at the two heavy leads. Remove jammed media Error 90X Software Error Unrecoverable software error.

Lexmark Error Codes

Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. by mcprinter on Apr 17, 2007 at 3:47am Add comment Please sign in to comment Please sign in to comment Lexmark Optra T610 Buy discount ink Buy this printer More Lexmark It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer. ERROR 23 Jam at the duplex unit.

If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. Youg | Premium Stream The theme of Shakespeare's sonnet #18 is similar to that of many of his other sonnets. If not present check in printer. I have downloaded the engine code and have attempted to send it to the printer, apparently withyout success.

Install maintenance kit and reset maintenance message Purchase Lexmark maintenance kits Error 82 Photo Developer Cartridge Exhausted The Photo Develper (OPC belt cartridge) has reached the end of it's life and Also, can I get some instructions on putting in the rollers. Remove the duplex front cover to access the jam area. http://support.lexmark.com/index?page=content&locale=en&productCode=OPTRA_T614&segment=SUPPORT&clearQuestion=Y&userlocale=EN_US&id=SO2001 Application Error en We're sorry for the inconvenience.

Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is If the test fails, the disk is defective or the data on track1 is bad. by stooge2990 on Jul 26, 2006 at 1:23pm Add comment Please sign in to comment 0 have you replaced the engine board previous to this error message? Generated Thu, 20 Oct 2016 07:04:02 GMT by s_wx1011 (squid/3.5.20)

Lexmark Crc Failed Do Not Power Off

We got it this morning and I have it installed. http://www.all-laser.com/aerrorlex/ May be due to the paper feeding manually while motors running and previous page in path. Lexmark Error Codes Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Lexmark Warranty Check Error 82 Photo Developer Cartridge Exhausted The Photo Develper (OPC belt cartridge) has reached the end of it's life and must be replaced.

Works great and certainly solved the problem (as I expected it would). -Alan A. have a peek at these guys Save $$ on every order! Check connecting cables for continuity. The printer display panel should read Programming Engine Code.Important: Do not power off the printer or press any buttons on the printer's LCD display panel during the code download.

Error 47 47 Font Card Removed While Printing Printer needs data on removed card. Replace the transfer roller as necessary. If a website you're hosting gets a DDoS attack or similar, thiseither a different hosting This is actually an instance of metaphor and imagery that is simpler than… Read more » http://jvmwriter.org/error-codes/lexmark-optra-t620-error-codes.html Load correct size Error 28 Input sensor not made after pick attempt.

Drop me a line and I'll email you it. Error 54 Serial Error - Framing or parity error on serial. I would appreciate any help....

Repairs Maintenance Computer Issues Experience Toner Guaranteed Pricing HP Laser Error Codes HP FAX Error Codes Lexmark Error Codes Canon Error Codes Okidata Error Codes Brother Error Codes Samsung Error Codes

The main motor assembly may need to be replaced. Engine Board 3. Houve um erro com o aplicativo. The instructions for sending the code to the printer says to copy source lptx /b and the printer should give a message the data is being copied.

Pay close attention to the area where the toner cartridge sits. If cables, connectors and connections are good replace assemblies listed. To do this: Go to the Lexmarkprinterfirmwarepage. this content Check the toner metering cam on back of suspect cartridge.

Error 38 38 Memory Full Memory used to store pages is full. Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 924 924 Fuser Error - Open circuit detected in thermistor circuit. Error Code Error Message Solutions ERROR 20 ERROR 200 Input Paper Sensor was not triggered - Paper may be jammed at the sensor. Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed.

Upload the firmware to the ptinter in the same way as the engine code, then upload the engine code. Originally Posted by ihavehemeroidserm and hope that the price The balanced chemical equation for the above reaction is:SO_2 (g) + 1/2 O_2 (g)… Read more » Cars & TrucksPost navigation← Older Requires further measurement The printhead (laser scanner) does not contain any serviceable parts. by unknown on Sep 27, 2004 at 6:39am Add comment Please sign in to comment i am having the same problem on the lexmark optra t612.

Run the Quick Disk Test. Error 59 Duplex Cover Open Top cover of duplex unit is sensed open. Make sure the memory shown on the printout matches the installed memory. The engine code is inside the toner door printed on the white label.

A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. Replace low voltage power supply assembly. Type usbutil [authorization code].pjl and press ENTER. (For the W812 for example,the command line should read usbutil eng204.pjl.) Note: For this step, you may need to download and install the USBUTIL Replace the disk if instructed by the operator panel.

Fuser errors can be from a cold fuser or an overheated fuser. A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. Otherwise, i think you should move to very bad idea.