Home > Error Codes > Laserjet 5si Error Codes

Laserjet 5si Error Codes


IID, IIID Only: 1. Replace any defective sensors or flags 13.21 DOOR OPEN JAM The top cover was open while printing 1. PCL file being sent to printer while in PostScript mode. 2. Replace or clean Pickup roller. 4. http://jvmwriter.org/error-codes/laserjet-4500-error-codes.html

Replace Formatter PCA. 4. Replace if either is bad. 4. Check that paper is not longer than 17.7 inches (450 mm), wider than 11.7 inches (297 mm), shorter than 3.9 inches (100 mm), or slimmer than 7.5 inches (191 mm). (These IIP Only: 1. http://www.printertechs.com/printer-troubleshooting/402-80-service-error-hp-laserjet-4-4plus-5-5si-8000

Hp Laserjet M1136 Mfp Error Codes E0

External fuser access door not closed. 4P/5P Only: 1. Paper Control PCA malfunction. 4V/4MV Only: 1. Clean all the paper guide plate areas, especially looking for possible labels stuck in the paper path area, or something simular. Replace Paper Control PCA (Solenoid/Sensor PCB Assembly). 4.

NOTE: After removing a sheet of paper you may need to check other areas to ensure that all paper has been removed. Check PostScript ROMs. 40 ERROR (DATA TRANSFER ERROR) 1. Verify the media meets the specifications. 5. Hp Laserjet M1132 Mfp Error E3 Check the pickup feed and separation rollers for unusual wear.

CLEARING TRAY 2 (OR TRAY 3) Open the tray. (Tray 2 is located above Tray 3, on the same side of the HP LaserJet 5Si Mopier as the control panel.) Remove Hp Laserjet M1132 Mfp Error E0 Cycle power. 4. The media is in poor condition. http://www.metrofuser.com/error-codes Replace the toner cartridge and close the top cover.

IIISi/4Si 1. Hp Printer Error Codes List Check Door Open sensor flag. You can print your Parts List or export to Excel to further work with him. Reseat connector J201 on Sensor PCA. 3.

Hp Laserjet M1132 Mfp Error E0

Plunger missing on top cover. 2. http://printcopy.info/?l=en&mod=free&chap=erc&brand=HP&model=LaserJet%205Si&page=1 Try turning over the stack of paper in the tray. Hp Laserjet M1136 Mfp Error Codes E0 After removing all pieces of the envelope or paper, replace the optional Envelope Feeder and toner cartridge. Hp Laserjet M1136 Mfp Error Codes E2 Wrong I/O cable. 3.

Close the tray. weblink Replace cable, AC Power Module to DC Controller, connector J208. (P/N RG1-0912-000.) IIP, IIP+, IIIP Only: 1. Sometimes the '80 Service Error' message is temporary, so try rebooting the printer and clearing any print jobs from the print queue.  If you continually see the error message, you should IIISi/4Si Only: 1. Hp Laserjet M1136 Mfp Error Codes E3

Check/replace SIMMs. 62.x memory error 4000/4050/4100/5000/8000/8100 only: 62.x where x = Dimm slot, Check/replace DIMMs. 63 SERVICE 1. Check the vertical transfer door (located on the right side of the 2000-sheet input tray, around the corner from where the tray pulls out) for additional damaged or jammed paper. You can add, delete list items and change the quantity of spare parts. navigate here Toner cartridge microswitch (SW501 on High Voltage PCA) malfunction. 3.

CLEARING THE MAILBOX WITH STAPLER Turn off the HP LaserJet 5Si Mopier and remove the Left Output Bin. Replace Paper Input PCA. 5. WARNING: Avoid touching the adjacent fusing area; it may be hot.

CLEARING THE TOP COVER Open the top cover.

This problem can be caused by software/drivers, memory PCA's, font macro personality cartridges, or optional I/O cards. 2. Use the Error Log Page and Error Codes to aid you in isolating where the errors are occurring. (See the "Error Log Page" section in Chapter 4 and the "Mopier Messages" Replace Main Motor PCA or Main Motor. 6. Check the entire paper path for other pieces of media in the path. 2.

If so, where you are getting the paper jam at? Replace optional I/O card. 43 OPT INTERFACE 1. II, III Only: If no jam visible: 1. http://jvmwriter.org/error-codes/lg-ru-44sz63d-error-codes.html Remove optional I/O PCA, then re-test. 69.x SERVICE 4000/4050/4100/5000/8000/8100 1.

If needed replace fuser or appropriate drive gears, or both. 7.