Home > Error Code > Lexmark X654de Error Codes

Lexmark X654de Error Codes

Contents

If the test fails, the disk is defective or the data on track1 is bad. Se ha producido un error en la aplicación. Simply match the error code that appears on your printer to the codes that are listed below. I would remove the fuser and check the sensor and the actuators free movement. check over here

Error 930 The wrong printhead is installed. Check fan for binding or defective bearing - Replace Fan How did we do? I have a Lexmark x642e MFP laser printer. Error 7X Network Card Codes These user codes are documented in various network card user manuals. https://www.marketpoint.com/lexmark-error-codes.aspx

Lexmark Error Codes

Cycle power Defective font card Defective system board 44 Font Card Error See 43 45 Downloaded Font Error Software setup Software drivers System board 46 Download Character Error See 45 47 We sell only remanufactured ink and compatible cartridges for Dell, HP, Canon, Epson and Lexmark printers. Verify latch relay is operating - slowly close door and listen for interlock switch 3. If the paper is not jammed in the duplex unit, then it may be jammed in the rear of the printer.

Fan the media and ensure it is properly installed. 2. Powered by WebJaguar B2B E-Commerce & B2C E-Commerce Solution by Advanced EMedia By using our site, you agree to our use of cookies. Possible repair actions 1. Lexmark Fax Error Codes Any help here would be appreciated too.

it Ci scusiamo per l'inconveniente. If the Quick Disk Test passes but the disk does not work, run the Disk Test/Clean (2 hr. Also, with all Lexmarks, make sure you have the current firmware. http://support.lexmark.com/index?page=content&id=SO6393 Mirror motor unable to reach operational speed, various other component level failures indicated by 935.XX Check cables, look for chafing or damage to ribbon cable at sharp bends around rear

Fan the media and ensure it is properly installed. 2. Lexmark Printer Error Code Ec5 Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the down position if applicable to your machine. Requires further measurement The printhead (laser scanner) does not contain any serviceable parts. Failing to plan is planning to fail!!!

Lexmark Printer Error Messages

Load correct size Error 28 Input sensor not made after pick attempt. We stock the full range of Lexmark service parts needed for preventive maintenance and repair service. Lexmark Error Codes Fuser errors can be from a cold fuser or an overheated fuser. Lexmark Engine Error Los Altos Hills, CA Thank you.

The feed and/or the retard roller might be dirty or used, this rolls loose friction during lifetime. check my blog See “Network Wrap Tests” on page 23. Replace the disk if instructed by the operator panel. All rights reserved. Lexmark Error Codes Problem

Go to sensor (input) lingering jam service check. Most Lexmark also have a yellow jumper on the sys board. de Wir entschuldigen uns für die Unannehmlichkeiten. this content There is no jam, it doesn't even attempt to pull paper up before it throws this error.

I am new to this and do not want to screw this up. Lexmark Printer Error Lights Remove jammed media Error 250 Paper Jam - Check MP Feeder Paper is jammed in the multipurpose feeder. by Andreas E on Dec 14, 2012 at 3:26am Add comment Please sign in to comment 0 I apologize, I saw the old posting for this printer and typed the wrong

Also, if the accumulated sheets are removed, the portion of the job printed after the jam will not be stapled.

br Lamentamos o inconveniente. We use brand names and model distinctions for non-OEM cartridges for the sole purpose of attesting printer compatibility. Check the operation of the toner sensor. 938.06 Service System Electronics Remove jammed media How did we do?

Make sure there is no paper jammed in the printer. Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22. by bcdub on Dec 14, 2012 at 7:52am Add comment Please sign in to comment 0 Error 202.13 means that the narrow media sensor, located in the fusing unit, is covered have a peek at these guys Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person.

Error 62 Disk Full Not enough disk space for data that has been requested to be written to disk. Newer machines display a sub code to indicate which condition applies. The fuser can usually be removed with two simple screws and the entire assembly lifted out. POR several times Check each board for secure ground.

See “Duplex” on page 2-16 Error 24 The defined paper size is too short to print data as formatted. It's the left of the two sensors inside the fuser paperway. Some 920.xx error codes may be cleared by turning the printer on and off and allowing it to complete POR. If one of these errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace

The time now is 06:18 AM. test). I truly appreciate it. Error 25 Input sensor made at wrong time.

The product was delivered just a few minutes ago. See “Network Wrap Tests” on page 23. I have had several bad sys boards over the past 2 years. Verify correct cable connections from the Engine board to the HVPS.

No inkjet error codes available Error Code Error Message Solutions ERROR 20 ERROR 200 Input Paper Sensor was not triggered - Paper may be jammed at the sensor. Pay close attention to the area where the toner cartridge sits. Power down the machine, move the yellow jumper over one pin, and reboot. Brand names for printer ink are just reference.

The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure. ERROR 23 Jam at the duplex unit. Replace the assys in the following order 1. Error 922 Fuser failed to reach standby temperature.