Home > Error Code > Lexmark X642e Error Codes

Lexmark X642e Error Codes

Contents

Make sure top access door is closed securely 2. The fuser can usually be removed with two simple screws and the entire assembly lifted out. it Ci scusiamo per l'inconveniente. If incorrect, install the cable correctly. check over here

Request Quote Error 920 920 Fuser Error indicates the Fuser is below temperature while printing. Pay close attention to the area where the toner cartridge sits. Check paper sensor flag for restricted movement or damage. What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account?

Lexmark Error Codes

C'è stato un errore con l'applicazione. Restore password × Upload manual upload from disk upload from url Thank you for your help! Error 38 38 Memory Full Memory used to store pages is full. Your cache administrator is webmaster.

Check the toner metering cam on back of suspect cartridge. Try opening Tray X. A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. Lexmark Engine Error FRU 1 ADF CCD cable 298.02 Error code service check Scanner missing—rear side cable unplugged.

The pin should enter the tower on the HVPS and depress the cover switch. Write down the information. 2. All rights reserved. Verify correct cable connections from the Engine board to the HVPS.

Note: Check for correct installation of the home sensor cable before proceeding with this service check. Lexmark Ms310dn Error Codes Error 47 47 Font Card Removed While Printing Printer needs data on removed card. Remove jammed media Error 250 Paper Jam - Check MP Feeder Paper is jammed in the multipurpose feeder. Works great and certainly solved the problem (as I expected it would). -Alan A.

Lexmark Printer Error Messages

Also, can I get some instructions on putting in the rollers. Replace the assys in the following order 1. Lexmark Error Codes Can be system board or printhead. Lexmark Fax Error Codes Please try the request again.

The product was delivered just a few minutes ago. check my blog May be due to the paper feeding manually while motors running and previous page in path. Service Error Codes Other Troubleshooting Tips 200 Paper Jam T65X Troubleshooting 201 Paper Jam Power Issue with Input and Output Options Installed 80 Scheduled Maintenance The Difference Between Fuser Type 1 Any help here would be appreciated too. Lexmark Error Codes Problem

Observe the lamp through the left near side of the printer. Run the Quick Disk Test. Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. this content If the problem persists, go to step 6. "Flatbed interconnect card "Home sensor removal" on 4-4.

Se ha producido un error en la aplicación. Lexmark Printer Error Code Ec5 Replace the Autocompensator Assy. See Action Check the cable for correct connections to the flatbed interface connector on the rear of the flatbed scanner assembly and to the motor driver card.

Generated Thu, 20 Oct 2016 03:03:23 GMT by s_nt6 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection

Error 122 Fuser Error - Problem in the fuser, not heating, heating to quickly or too hot. Error 63 Unformatted or Defective Disk The printer will ignore a disk it senses as defective. Check the flatbed CCD assembly for any signs of damage and for proper mechanical operation. Lexmark Printer Error Lights Check the fuser lamp is the correct type of lamp that should be installed. • Verify the line voltage is not exceeding the maximum rating for the printer.

Diagnostic information 7002-xxx 2-115. 2-116. 4-48. "848.00 2-13 Previous page Next page 1...474849505152535455 Also See for Lexmark X642e Lexmark X644e User Manual 191 pages Lexmark X642E Quick Reference 5 pages Replace Printhead Pricing Error 931 Printhead error - No first sync - check connections at both ends of cable for corrosion or oxidation. Service errors 980 thru 984 < device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. > have a peek at these guys I will have purchasing call in an order.