Home > Error Code > Lexmark X342 Error Codes

Lexmark X342 Error Codes

Contents

Remove the scanner assembly. Index Numerics 2xx paper jams 2-9-?? 3x-9x attendance messages 2-10-2-11 9xx service errors ... 3-5 NVRAM reset 3-6 print debug 3-5 power supply ID 3-4 printer model 3-4 registration 3-6 printer Service error codes (9xx) Error Description 900 Service RIP software 900 Service (No Modem) 902 General engine software failure 914 DC Pick Motor 917 Transfer roll 920 Fuser Error Indicates that Contact your second level support to obtain the latest firmware build. weblink

Replace the Autocompensator Assy. Carefully place the MFP on its back with the bottom of ... Note: Notice the alignment of the printhead at each screw before removing the screws. es Lamentamos las molestias.

Lexmark Fax Error Codes

Go to "Printer Model" on page 3-4. Remove the rear cover. roll and input to the fuser for anything that might cause the paper to remain over the input.... • A defective input sensor. 200.02 200.04 2-14 Service Manual manuals4you...Lexmark X342N | Remove the paper tray.

more information. voltage or ground is not present, see "Controller card service check" on page 2-21 for more information. DU DU xx xx xx xx xx xx xx xx To identify the bytes: Byte 1 ...Lexmark X342N | Service Manual - Page 36...message 200.00 200.01 Explanation Paper jam around input Error Code 700 Error In Fax Transmission Home | My Manuals | Manual Index | Manual Categories | About Us | Contact Us | Privacy Application Error en We're sorry for the inconvenience.

Go to "Fuser service check" on page Check cabling and connectors. See "Controller card service check" on page 2-21 for more information. CAUTION This type of caution indicates a tipping hazard. Go to page 2-23.

Perform the following steps to reset the FAX NVRAM. 1. Fax Error Codes Ricoh There was an error with the application. In general, fuser errors require replacement of the fuser as a cost effective repair. See "Left side cover removal" on page 4-3. 2.

Lexmark Error Codes

Remove the modem card. Always print a page from each paper source following a repair action. Lexmark Fax Error Codes It may also indicate a problem in the transfer roll area. Lexmark Fax Error E-724 Action Lift flatbed cover and move the ...If this does not remedy the problem see "ADF service check" on page 2-19. 2-8 Service Manual manuals4you.comLexmark X342N | Service Manual - Page

The fuser, melts or fuses the toner to the media and has a heat roller and a pressure roller. have a peek at these guys Unplug the cable at the motor, and install the new cable. 4-34 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 1077003-XXX Scanner ADF paper tray removal 1. Place the sheet of light blue paper in ...Lexmark X342N | Service Manual - Page 68... Make sure the memory shown on the printout matches the installed memory. Lexmark Fax Error E970

Machine type and model 7003-100 7003-050 7003-110 Description Lexmark X340 Lexmark X340n Lexmark X342n Parts catalog 7-1Lexmark X342N | Service Manual - Page 1447003-XXX Assembly 1: Covers 7-2 Service Manual manuals4you.comLexmark The following illustration shows the correct registration. 3-8 Service Manual manuals4you....Lexmark X342N | Service Manual - Page 69... Remove the screw (E) and ADF cable clamp. 8. check over here Repair information 4-37Lexmark X342N | Service Manual - Page 1107003-XXX Scanner ADF top cover removal 1.

access cover will not close Fuser parts melted Toner not fused to the paper Blank page Black page Heavy background ... T2 Timeout Occurred Due To Loss Of Command/response Synchronization. cover Optional drawer 2 assembly (no tray) Optional tray 2 Main tray Left side cover Legal extender cover Parts catalog 7-3Lexmark X342N | Service Manual - Page 1467003-XXX Assembly 2: Scanner Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22.

Change the media texture setting.

Repair information 4-15 manuals4you.comLexmark X342N | Service Manual - Page 88.... 3. See "Hot fuser service check" on page 2-24. Gently remove the geared belt from the CCD. Fax Error Code E-713 I will have purchasing call in an order.

Reboot MFP ... The laser system and printer are designed so there is never any ...Lexmark X342N | Service Manual - Page 8...condicões de assistência prescritas. right margin equals -8. this content Units/mach: ...

Paper jam near Tray 1 241.00 241.12 ... See "... Note: The main motor is not a service part. See "Front access cover removal" on ....

If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages.