Home > Error Code > Lexmark X340 Error Codes

Lexmark X340 Error Codes

Contents

Reconnect. Error 52 Flash Full - Not enough flash memory for data requested to be stored. PRECAUCIÓN: este símbolo indica que el voltaje de la parte del equipo con la que está trabajando es peligroso. Remove the left side cover. weblink

If the paper is not jammed in the duplex unit, then it may be jammed in the rear of the printer. check the LVPS/HVPS. Newer machines display a sub code to indicate which condition applies. If changing the toner cartridge doesn't fix the problem, check pin 1 in J17 for +5V.

Lexmark Error Codes

Verify discontinuity ... Dan Erim Ortiz 518 προβολές 7:00 Lexmark E260, E360, E460, X264, X363 Fuser and Heat Errors (920 - 925) - Διάρκεια: 14:14. See "LVPS/HVPS service check" on page 2-25 • If the grounds ...-15 seconds in the following sequence: 1. We stock the full range of Lexmark service parts needed for preventive maintenance and repair service.

Buy the Full Version You're Reading a Free Preview Pages 68 to 78 are not shown in this preview. Place a sheet of paper around the transfer roll to protect it. 3. Method Fax Fwd Fax Footer Auto Reduce Confirmation Calr ID Ptrn Auto Prt Rpt Network Setup Enable DHCP IP Address Netmask Gateway Paper Setup Size / Type Tray Link Paper Texture Lexmark Fax Error E970 Close the front cover until it locks.

Error 901 Engine Flash Indicates the Flash with the system code program is defective Replace System Board Request Quote Error 914 DC Pick Motor - No Encoder Feedback Check the Lexmark Fax Error Codes Check the fuser lamp is the correct type of lamp that should be installed. • Verify the line voltage is not exceeding the maximum rating for the printer. See "Paper exit guide assembly removal" on page 4-31 for more ...Slide the fuser out far enough to expose and disconnect the AC cable connections. 6. http://support.lexmark.com/index?pmv=print&page=content&locale=en&userlocale=EN_US&id=SO4340 Remove the ADF pick roll.

Pull the plastic retaining tab back, place a flat blade screwdriver in the notch on the metal pin. 10. Error Code 700 Error In Fax Transmission Make sure the flag is operating freely and is correctly installed. To cancel the job, press Stop. Note: The printer does not need a POR to enter diagnostics mode.

Lexmark Fax Error Codes

Error 25 Input sensor made at wrong time. Visit Website While prying the rear cover back, slide the modem card down, and remove the modem card from the MFP. 4-54 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 127... 4-30. Lexmark Error Codes If the pieces come apart, they can be easily reassembled if necessary. 4-28 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 101...the controller card. Lexmark Printer Error Messages Make sure the memory shown on the printout matches the installed memory.

Repair information 4-15 manuals4you.comLexmark X342N | Service Manual - Page 88.... 3. http://jvmwriter.org/error-code/lexmark-t640-error-codes.html La informació pel ...Lexmark X342N | Service Manual - Page 14... Use a small Phillips screwdriver to remove the screw (A) that secures the sensor to the printer frame. 5. If the leading edge of the paper is damaged, instruct the user to lessen the number of documents ...extender are properly installed. Lexmark Fax Error E-724

de Wir entschuldigen uns für die Unannehmlichkeiten. If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed. Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is check over here Replace the assys in the following order 1.

Load print media into the manual feeder. Fax Error Codes Ricoh Printer driver set to letter when A4 paper is loaded. • Pre staged paper in the tray. 200.15 84 xx 30 00 00 00 84 xx ...Lexmark X342N | Service Manual Remove rear cover.

We can email further info if needed for your particular model.

Remove rear cover. To enable this setting, perform the following steps: 1. For example 3-1 indicates assembly 3 and the item number 1. Lexmark Error Codes Problem Lift the operator panel assembly up, and gently pull it away from the scanner top. 4-30 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 103...

clear a paper jam or to uninstall the option. • The option may be attached to the MFP, but a communications problem may.... default menu item. Press . this content Check fan for binding or defective bearing - Replace Fan How did we do?

Check the media type and texture settings on the MFP and in the driver. Remove the paper exit guide assembly. front of the lower right side cover. 3. Replace Printhead Pricing Error 934 Printhhead Error - Lost Lock condition Indicates a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system

If the setting is not in your driver, you can download the correct Lexmark setup utility from the Lexmark Web site at www.lexmark.com. the card assembly. General information The Lexmark™ X340, X340n, and X342n are MFPs that combine print, scan, copy, e-mail, and fax ...7003-050 Lexmark X340n 64MB 7003-110 Lexmark X342n 64MB Note: Optional memory, flash memory, Error 54 Serial Error - Framing or parity error on serial.

J3 ADF Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ... Make sure the memory shown on the printout matches the installed memory. If an open circuit, replace the lamp or fuser. Buy the Full Version You're Reading a Free Preview Pages 82 to 84 are not shown in this preview.

John D. Remove two screws (B) located on the rear of the scanner top. 7. Operator panel service check FRU Operator panel Controller card Action Buttons Check... B A A B 5.

Remove the clip (B) from...Lexmark X342N | Service Manual - Page 96..., remove the screw (A) behind the ACM (auto compensator) pivot that holds the paper sensor in place. Press and...Lexmark X342N | Service Manual - Page 62... Carefully lift the cover free from the printer base frame. 4-2 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 757003-XXX 6. See "Rear cover removal" on page 4-5. 2.

Engine Board 3.