Home > Error Code > Lexmark T632 Error Codes

Lexmark T632 Error Codes

Contents

Service error code Error code 900 RIP Software 901 Engine Flash 902 General Engine Software Error 903 Paperport Link Driver Error 904 Interface Violation by RIP 905 Interface Violation by Paperport The system returned: (22) Invalid argument The remote host or network may be down. Thank you and your firm again, you were terrific. See Page 2-19 in the service manual Replace the high voltage power supply Replace system cable 2 (NOTE: the HVPS and system cable 2 can be checked by checking continuity across check over here

Email us using our onlie contact form - we'd be happy to help you troubleshoot any issue you are having with your Lexmark printer. 22 Paper Out or Paper Jam Check We got it this morning and I have it installed. The printer is set for (hardware or software) Defective D-roller Debris in the paper path Gears not turning or broken gear Defective paper tray Broken input sensor flag Defective input sensor If the test fails, the disk is defective or the data on track1 is bad. http://www.all-laser.com/aerrorlex/

Lexmark Error Codes

Replace the system board. Check the TMC pin in the cartridge contact error for free non binding movement If pin does not move freely you may need to replace the contact assembly. May require service technician Press "GO" to clear message and temporarily continue Install Transfer Drum Unit Error 88 Toner Low Toner sensor detects low toner.

The fuser assembly is subject to mechanical wear and heat related degradation and is a scheduled replacement item in most machines at between 200K and 350K pages. Error 44 Defective font card installed in font slot. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Lexmark Crc Failed Do Not Power Off Go to on page 2-94.

Service errors 980 thru 984 < device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. > Lexmark Printer Error Messages I truly appreciate it. There was an error with the application. http://support.lexmark.com/index?productCode=LEXMARK_T630&segment=SUPPORTproductCode%3D&page=content&id=SO2206&locale=EN&userlocale=EN_US Go to Check the integrated paper tray (Tray 1) for correct paper loading.

it Ci scusiamo per l'inconveniente. Lexmark Printer Error Code Ec5 If others want MI DC 101 too , here's http://pdf.ac/4QCMp6 × Bookmark × Please, turn your attention By pressing 'print' button you will print only current page. Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. If either the 936 error or the 937 error returns after you power on the printer or when you try to print, the printer will require service.

Lexmark Printer Error Messages

Error Codes 910, 911, 912, 913, and 914 are indications that a Tray 1 paper feed problem has been detected. Error 24X Paper Jam - Check Tray "X" Primary: Paper is jammed around Tray X (X=tray 1 thru 5). Lexmark Error Codes I am new to this and do not want to screw this up. Lexmark Engine Error Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers

Request Quote 947 Engine Board Engine board failure Replace the Engine Board Request Quote 953-954 NVRAM Failure NVRAM Failure 953: NVRAM Chip Failure 954: NVRAM CRC Failure Optra T 640/642/644 check my blog We stock the full range of Lexmark service parts needed for preventive maintenance and repair service. Your cache administrator is webmaster. Uploaded by: Daniel Hide thumbs Also See for T632 Quick manual - 4 pagesReference manual - 459 pagesService manual - 345 pages 1 2 3 4 5 6 Lexmark Error Codes Problem

Error 26 Duplex unit is installed but paper tray is not sensed. Replace Printhead Pricing Error 934 Printhhead Error - Lost Lock condition Indicates a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system Es gab einen Fehler bei der Anwendung. this content Replace the bump alignment motor Replace bump motor Replace interlock switch Replace System Card Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex

Also, if the accumulated sheets are removed, the portion of the job printed after the jam will not be stapled. Lexmark Printer Error Lights Replace defective cartridge. Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person.

John D.

Simply match the error code that appears on your printer to the codes that are listed below. Replace the system board. Il ya eu une erreur à l'application. 938.06 Service System Electronics Check the operation of the toner sensor.

Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22. If you have other tech support questions that are not covered here, send email to [email protected] The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure. http://jvmwriter.org/error-code/lexmark-w850-error-codes.html Make sure fuse is installed correctly, Verfy proper fuser is being used.

Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the down position if applicable to your machine. Reload the paper and do a power on reset. Any help here would be appreciated too. Can be system board or printhead.

No inkjet error codes available Error Code Error Message Solutions ERROR 20 ERROR 200 Input Paper Sensor was not triggered - Paper may be jammed at the sensor. Indicates that the fuser is below standby temperature when the printer is idle. br Lamentamos o inconveniente.