Home > Error Code > Lexmark T614 Error Codes

Lexmark T614 Error Codes

Contents

If cables, connectors and connections are good replace assemblies listed. Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. Requires further measurement The printhead (laser scanner) does not contain any serviceable parts. Los Altos Hills, CA Thank you. weblink

The fuser, melts or fuses the toner to the media and has a heat roller and a pressure roller. Check the toner metering cam on back of suspect cartridge. Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22. Works great and certainly solved the problem (as I expected it would). -Alan A.

Lexmark Error Codes

Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 927 Main Fan Stalled, Cartridge Fan or RIP fan stalled, Power off and manually spin fan - it ERROR 23 Jam at the duplex unit. The fuser can usually be removed with two simple screws and the entire assembly lifted out. Error 30 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed properly and that it is detected by the ramp on

Replace Printhead Pricing Error 935 Printhead Error - May have sub-codes. Reload the paper and do a power on reset. Houve um erro com o aplicativo. Lexmark Error Codes Problem The main motor is located just to the left of the toner cartridge.

Run the Quick Disk Test. Lexmark Printer Error Code Ec5 If the paper is not jammed in the duplex unit, then it may be jammed in the rear of the printer. Remove jammed media How did we do? here Remove the duplex front cover to access the jam area.

Controller Board 2. Lexmark Printer Error Lights We can email further info if needed for your particular model. Also, can I get some instructions on putting in the rollers. It can also be the LVPS (low voltage power supply) or a fuse in the power supply on some models.

Lexmark Printer Error Code Ec5

Error 921 Fuser is below standby temperature when idle. http://support.lexmark.com/index?page=content&id=SO4438&userlocale=EN_US&segment=SUPPORT&productCode= Remove jammed media Error 90X Software Error Unrecoverable software error. Lexmark Error Codes In general, fuser errors require replacement of the fuser as a cost effective repair. Lexmark Printer Error Messages Replace low voltage power supply assembly.

de Wir entschuldigen uns für die Unannehmlichkeiten. have a peek at these guys Check fan connector and cable for loose or damaged connection. Verify correct cable connections from the Engine board to the HVPS. Mirror motor unable to reach operational speed, various other component level failures indicated by 935.XX Check cables, look for chafing or damage to ribbon cable at sharp bends around rear Lexmark Engine Error

If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure. Error 38 38 Memory Full Memory used to store pages is full. check over here Install more memory Simplify print job Delete fonts, macros and other data stored in RAM Error 39 Page too complex to print.To verify that the printer recognizes all the installed memory,

Newer machines display a sub code to indicate which condition applies. Lexmark Crc Failed Do Not Power Off Verify latch relay is operating - slowly close door and listen for interlock switch 3. Transfer Roll Error Cannot start servo operation.

If the test fails, the disk is defective or the data on track1 is bad.

Any help here would be appreciated too. Se ha producido un error en la aplicación. New service manuals Canon i-SENSYS LBP712Cx, (sm, pc), Eng, 36.2Mb Canon MF419dw, (sm, pc), Eng, 30.6Mb Kyocera-Mita ECOSYS M6035cidn, (sm, pc), Eng, 137Mb Samsung SLM4025NX, (sm, pc), Eng, 26.8Mb Samsung SLM3320ND, 938.06 Service System Electronics Roller is approximately 2" in circumference print defects with this repetitive spacing can be caused by transfer roller problems, on a standard 11" page defect would repeat five times.

I will have purchasing call in an order. POR several times Check each board for secure ground. Error 80 Printer has reached 200,000-300,000* prints without maintenance count reset. this content Perform fuser service check.

Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults. The system returned: (22) Invalid argument The remote host or network may be down. Error 44 Defective font card installed in font slot. There was an error with the application.

The fuser assembly is subject to mechanical wear and heat related degradation and is a scheduled replacement item in most machines at between 200K and 350K pages. All rights reserved. Your cache administrator is webmaster. Request Quote 947 Engine Board Engine board failure Replace the Engine Board Request Quote 953-954 NVRAM Failure NVRAM Failure 953: NVRAM Chip Failure 954: NVRAM CRC Failure Optra T 640/642/644