Home > Error Code > Lexmark Printer Error Messages

Lexmark Printer Error Messages

Contents

Error 30 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed properly and that it is detected by the ramp on The All-In-One can scan up to 19200 dpi, so it is possible to exceed the amount of data a file can hold. Press the Power button. Click See More Scan Settings. weblink

For non-touch-screen printer models, press to confirm.Maintenance kit very low, [x] estimated pages remain[80.xy]You may need to replace the maintenance kit very soon. File is too large You have exceeded the amount of data a scan file can hold. Is the receiving fax machine out of ink? For non-touch-screen printer models, press to confirm.Turn off the printer, wait for about 10 seconds, and then turn the printer back on.Update the network firmware in the printer or print server. https://www.marketpoint.com/lexmark-error-codes.aspx

Lexmark Printer Error Code Ec5

Open the printer rear door to access the jam. Make sure the cartridges are snapped into place in the carrier. Error 80 Printer has reached 200,000-300,000* prints without maintenance count reset.

Error 920.X and 922.XX may display for a cold fuser. Contact system administrator.Try either of the following:From the printer control panel, select Continue to clear the message. Press Stop/Clear on the control panel to cancel printing. 938.06 Service System Electronics Error message or title What it indicates Solution Ink low The print cartridge is running out of ink.

Click OK. Lexmark Engine Error For more information, see the "Replacing supplies" section of the User's Guide.If necessary, select Continue on the printer control panel to clear the message and continue printing. Shop for Lexmark Maintenance kits * This is a model dependent interval Install maintenance kit and reset maintenance message Purchase Lexmark maintenance kits How did we do? Check for 24V at red wire on interlock switch with door closed 4.

From the Color depth drop-down menu, select Gray. Lexmark Crc Failed Do Not Power Off Check the operation of the toner sensor. For help, see Using the Lexmark Solution Center. If you are printing on inkjet paper, select Quick Copy from the Quality/Copies tab of Properties, Preferences, Options, Setup or from the All-In-One Center.

Lexmark Engine Error

Make sure the second box is checked to remove image patterns from magazine or newspaper documents. http://publications.lexmark.com/publications/pdfs/4200/eng/trouble.html Check fan for binding or defective bearing - Replace Fan How did we do? Lexmark Printer Error Code Ec5 Press Select to select a new blank paper size, or press Stop/Clear to cancel the current DPOF print job. Lexmark Error Codes Problem Is the original document loaded correctly?

For help, see Replacing the print cartridges. have a peek at these guys Is Call Waiting interfering with fax transmission? For non-touch-screen printer models, press to confirm.Turn off the printer and then turn it back on.Update the network firmware in the printer or print server. Check connections to the to interconnect card assembly. Lexmark Printer Error Lights

Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. Make sure the print quality settings on the receiving fax machine are satisfactory. From the Maintenance tab, click Print a Test Page. check over here Replace Printhead Pricing Error 932 Lost hsync No High voltage signal - check connections at both ends of cable for corrosion or oxidation.

For more information, visit the Lexmark support Web site at http://support.lexmark.com.No analog phone line connected to modem, fax is disabled.Connect the printer to an analog phone line.Non-Lexmark[supply type], see User's Guide[33.xy]Note:The Lexmark Ms310dn Error Codes Load the original face down in the ADF. Are the fax number, country code, and date/time set correctly?

If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door.

Display language is not preferable If the language on the All-In-One display is not the language you prefer, follow these steps to change it: On the control panel, press Options until Replace the toner cartridge.Reinstall missing or unresponsive imaging unit[31.xy]Try one or more of the following:Check if the imaging unit is missing. The fuser can usually be removed with two simple screws and the entire assembly lifted out. Lexmark Fax Error Codes Choose the appropriate blank paper size.

For non-touch-screen printer models, press to confirm.Select Scan from automatic feeder to continue scanning from the ADF immediately after the last successful scan job. Black and white copy quality is unsatisfactory You might need to change an Advanced Copy Setting in the All-In-One Center. If the printer cannot find a tray that has the correct size and type of paper, then it prints from the default paper source.Cancel the current job.Load [paper source] with [paper this content For scanning: From your desktop, double-click the Lexmark4200 Series All-In-One Center icon.

Requires further measurement The printhead (laser scanner) does not contain any serviceable parts. Use the right arrow to scroll through the list of languages. See Loading an original document into the ADF. Whatever the cause, you can usually override the error by following a few troubleshooting steps.

To check All-In-One status: Click Start Settings Printers. Replace the print cartridge with a new cartridge. Can be system board or printhead. Open the Lexmark Solution Center.

Are both your All-In-One and computer on? Unplug your All-In-One from the wall outlet. It can also be the LVPS (low voltage power supply) or a fuse in the power supply on some models. Error 63 Unformatted or Defective Disk The printer will ignore a disk it senses as defective.

If the Quick Disk Test passes but the disk does not work, run the Disk Test/Clean (2 hr. Open doors and covers and remove the toner cartridge.