Home > Error Code > Lexmark Optra T612 Error Codes

Lexmark Optra T612 Error Codes

Contents

by aerolaser on Jan 26, 2009 at 12:21pm Add comment Please sign in to comment 0 The network card (separate or integrated) can sometimes cause these errors. Remove jammed media Error 90X Software Error Unrecoverable software error. what am i doing wrong? This can also be reflashed but in the majority of the cases the RIP board will also need to be replaced as the network card is built in. check over here

i need the code for the Lexmark Optra T612. If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages. It consists of four small momentary buttons that are engaged by the metal. There is a open slot in the black plastic, you should see a black flag in the UP position when there is no paper there.

Lexmark Error Codes

Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the down position if applicable to your machine. Make sure the memory shown on the printout matches the installed memory. Can be system board or printhead.

C'è stato un errore con l'applicazione. Any help? Try opening Tray X. Lexmark Engine Error The fuser can usually be removed with two simple screws and the entire assembly lifted out.

Error 38 38 Memory Full Memory used to store pages is full. Lexmark Invalid Engine Code Mode If the 902 error does return, please go through the checklist below. If that does not work you will need to replace the input tray board because the Optra T612 does not give you the ability to override the auto tray size feature.sometimes http://support.lexmark.com/index?page=content&id=SO1632 See “Network Wrap Tests” on page 23.

Perform fuser service check. Lexmark Dc Pick Motor Secondary: When this message is displayed, do not remove accumulated sheets during the jam clearance procedure as the printer will not reprint the removed sheets. alright use your left hand hold the right menubutton, selectbutton, and ReturnButton this will force the printer to enter a boot wait mode (means wait for the firmware)if you have any FYI we have seen this error when someone tries to print a PDF file scanned from certain copiers.

Lexmark Invalid Engine Code Mode

Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. Run the Quick Disk Test. Lexmark Error Codes email with model, primary and secondary pattern for troubleshooting info. Lexmark Printer Error Messages Check the wiring harness cable.

In other cases it will only fix the problem for a few mins and in this case the only fix is to replace the RIP board which is extremely costly and check my blog The first plan of action is to try the firmware reflash and a lot of the time this will solve the problem. would not copy go into program mode otherwise by unknown on Apr 21, 2006 at 2:30pm Add comment Please sign in to comment 0 Hi, I am dealing with the same The transfer roller is included in the maintenance kit. Service Error 146.00 Dc Pick Motor

The metal engages a little pcb called the Input Tray Board. If reinstalling the engine code on the printer does not fix the problem,you can perform an NVRAM on the printer. Cycling the power was the only way for me to get rid of the error. this content by unknown on Apr 30, 2009 at 6:16am Add comment Please sign in to comment 0 I believe this is just a stupid error trick...I send a lot of jobs to

Scroll Down to your error code.... Lexmark Error Codes Problem Roller is approximately 2" in circumference print defects with this repetitive spacing can be caused by transfer roller problems, on a standard 11" page defect would repeat five times. I had a similar (maybe the exact same) problem three or four years ago and was told that was what I needed to do.

To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page.

by unknown on Apr 29, 2005 at 3:49pm Add comment Please sign in to comment 0 Hi everyone here is a proposition to solve the problem :To download the needed file by unknown on Aug 29, 2002 at 1:57pm Add comment Please sign in to comment 0 I followed the instruction, but when I did " COPY 7892B25L.PJL >LPT1: /b" it gave Replace printhead, system board or ribbon cable. Lexmark Printer Error Code Ec5 Remove jammed media Error 250 Paper Jam - Check MP Feeder Paper is jammed in the multipurpose feeder.

Check fan for binding or defective bearing - Replace Fan How did we do? would not clear ..hold down "go & return" then turn power on. No inkjet error codes available Error Code Error Message Solutions ERROR 20 ERROR 200 Input Paper Sensor was not triggered - Paper may be jammed at the sensor. have a peek at these guys To do this: Go to the Lexmarkprinterfirmwarepage.

Once you flip it over this will make sense. My company asked if I wanted the machine. This has worked every time. Wayne Haub Kansas City Save time and money by servicing your own Lexmark printer Lexmark Laser Printer Error Codes Lexmark error codes may not apply equally to all models.

All rights reserved. Drop me a line and I'll email you it. by unknown on Apr 13, 2006 at 12:30pm Add comment Please sign in to comment Have you tried turning round the charge roller?Could also be a bad eathing point to the There was an error with the application.

It has it's own separate NVRAM, and can be reset separately.You will lose all your network settings, of course, so print a network settings page first.* Power cycle, sometimes this doesn't Check the toner metering cam on back of suspect cartridge. Controller Board 2. I have tried too many things I read in other posts, and your post was the exact solution.

by unknown on Jul 30, 2005 at 6:09am Add comment Please sign in to comment 0 Actually, there is a cheaper solution.Just take the network card out and hook the printer by Anonymous on Apr 10, 2007 at 11:10am Add comment Please sign in to comment C510 931 error normally means a problem with the printhead...but C510 is a pretty cheap machine, thank you by Anonymous on May 6, 2008 at 4:40am Add comment Please sign in to comment 0 931 services printed error.Thank you..thank you.. Check connecting cables for continuity.

Check for 24V at red wire on interlock switch with door closed 4. by mcprinter on Apr 17, 2007 at 3:47am Add comment Please sign in to comment Please sign in to comment Lexmark Optra T610 Buy discount ink Buy this printer More Lexmark We can email further info if needed for your particular model. Ich würde an deiner Stelle mal ernsthaft drüber nachdenken, wie du hier im Moment arbeitest.Mit freundlichen GrüßenKind regardsS pozdravemi.A.

The fuser is the main part of a printer maintenance kit.