Home > Error Code > Lexmark Optra Laser Printer Error Codes

Lexmark Optra Laser Printer Error Codes

Contents

If the test fails, the disk is defective or the data on track1 is bad. The pin should enter the tower on the HVPS and depress the cover switch. Check the continuity of the fuser lamp at the two heavy leads. Error 200 & 201 – Paper Jam An error 200 message appears if there is paper blocking the pathways of the printer. weblink

The fuser can usually be removed with two simple screws and the entire assembly lifted out. Shop for Lexmark print cartridges Error 32 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer. Can also be LVPS or system board. Replacement of the thermistor is not a cost effective repair, replace fuser assembly.

Lexmark Engine Error

Escher? Please try the request again. If either the 936 error or the 937 error returns after you power on the printer or when you try to print, the printer will require service. Works great and certainly solved the problem (as I expected it would). -Alan A.

Replace low voltage power supply assembly. Open the printer rear door to access the jam. br Lamentamos o inconveniente. Lexmark Dc Pick Motor If the test fails, the disk is defective or the data on track1 is bad.

blog comments powered by Disqus About the author A nerdy and self-proclaimed geek who thinks ink and toner should cost less so he started 247inktoner.com. Lexmark Error Codes Problem An error 201 is an indication that paper is jammed between input sensors: between the front and back input sensors. POR several times Check each board for secure ground. Error 82 Photo Developer Cartridge Exhausted The Photo Develper (OPC belt cartridge) has reached the end of it’s life and must be replaced.

Verify correct cable connections from the Engine board to the HVPS. Lexmark Crc Failed Do Not Power Off Error 47 47 Font Card Removed While Printing Printer needs data on removed card. ERROR 22 The exit sensor was not unmade in time. Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed.

Lexmark Error Codes Problem

Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. We stock the full range of Lexmark service parts needed for preventive maintenance and repair service. Lexmark Engine Error Your cache administrator is webmaster. Lexmark Printer Error Code Ec5 Load correct size Error 28 Input sensor not made after pick attempt.

If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages. http://jvmwriter.org/error-code/laser-printer-error-code.html Check connections to the to interconnect card assembly. Request Quote 947 Engine Board Engine board failure Replace the Engine Board Request Quote 953-954 NVRAM Failure NVRAM Failure 953: NVRAM Chip Failure 954: NVRAM CRC Failure Optra T 640/642/644 My Account| Cart| Order Status Market Point Search: select Advanced search Read Customer Reviews GSA Contract Schedule Enter Here Need Assistance? Lexmark Printer Error Lights

Turning off the printer for ten minutes or longer should clear the error. Scroll Down to your error code.... If the Quick Disk Test passes but the disk does not work, run the Disk Test/Clean (2 hr. check over here There should be zero ohms resistance between the transfer roll shaft and the high voltage supply contact.

Check the operation of the toner sensor. Lexmark X658de Error Codes Lexmark Lamps Error 927 Main Fan Stalled or Cartridge Fan stalled, Check fan for binding or defective bearing - Replace Fan Error 928 Erase lamp assembly missing or disconnected Error Replace Printhead Pricing Error 934 Printhhead Error - Lost Lock condition Indicates a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system

Generated Tue, 18 Oct 2016 17:40:26 GMT by s_ac4 (squid/3.5.20)

Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex Unit. Generated Tue, 18 Oct 2016 17:40:26 GMT by s_ac4 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection Make sure the memory shown on the printout matches the installed memory. Lexmark Ms310dn Error Codes Replace printhead or ribbon cable.

Replace the disk if instructed by the operator panel. Error 27 Envelopes/paper loaded are wrong size. Es gab einen Fehler bei der Anwendung. http://jvmwriter.org/error-code/laser-printer-error.html Transfer Roll Error Cannot start servo operation.