Home > Error Code > Lexmark Optra 410 Error Code

Lexmark Optra 410 Error Code

Contents

Check fan connector and cable for loose or damaged connection. Thank you and your firm again, you were terrific. If the paper is not jammed in the duplex unit, then it may be jammed in the rear of the printer. If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. weblink

Remove jammed media Error 90X Software Error Unrecoverable software error. Make sure the memory shown on the printout matches the installed memory. Fuser errors can be from a cold fuser or an overheated fuser. Replace Printhead Pricing Error 936 Error 937 Error 936/937 Main Drive Motor, Transport Motor An error with the main drive motor has been sensed by the printer Optra s 2450 Optra

931.01 Service Printhead Error

Mirror motor unable to reach operational speed, various other component level failures indicated by 935.XX Check cables, look for chafing or damage to ribbon cable at sharp bends around rear Error 52 Flash Full - Not enough flash memory for data requested to be stored. New service manuals Kyocera-Mita ECOSYS P6035cdn, (sm, pc), Eng, 117Mb Samsung Xpress M2870FD, (sm, pc), Eng, 12.7Mb Samsung Xpress M2820DW, (sm, pc), Eng, 11.1Mb HP LaserJet Enterprise MFP M527, (srm, stm, Replace the disk if instructed by the operator panel.

Check fan for binding or defective bearing - Replace Fan How did we do? Create your Spare Parts List. See “Network Wrap Tests” on page 23. Lexmark X658de Error Codes May require service technician Press "GO" to clear message and temporarily continue Install Transfer Drum Unit Error 88 Toner Low Toner sensor detects low toner.

Check LVPS cable for continuity. Lexmark Error Codes You can add, delete list items and change the quantity of spare parts. es Lamentamos las molestias. A secondary error indication can be obtained by pressing an releasing a button.

May be due to the paper feeding manually while motors running and previous page in path. Lexmark Engine Error Try opening Tray X. If either the 936 error or the 937 error returns after you power on the printer or when you try to print, the printer will require service. Check connecting cables for continuity.

Lexmark Error Codes

Replace Printhead Pricing Error 932 Lost hsync No High voltage signal - check connections at both ends of cable for corrosion or oxidation. It was previously plugged to a switch with no problems. 931.01 Service Printhead Error Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Lexmark Printer Error Messages Error 922 Fuser failed to reach standby temperature.

We do not sell these spare parts.We help you to create your parts sheets to request from your suppliers. http://jvmwriter.org/error-code/lexmark-error-code.html Remove toner cartridge for better access to jammed paper. Can be system board or printhead. Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. Service Error 146.00 Dc Pick Motor

Check paper sensor flag for restricted movement or damage. Request Quote 947 Engine Board Engine board failure Replace the Engine Board Request Quote 953-954 NVRAM Failure NVRAM Failure 953: NVRAM Chip Failure 954: NVRAM CRC Failure Optra T 640/642/644 It may be necessary to remove the re drive assembly to observe the lamp cycling on and off. check over here Your cache administrator is webmaster.

Replace with the correct printhead. Lexmark Dc Pick Motor Error 921 Fuser is below standby temperature when idle. Power printer off one to two minutes.

Verify correct cable connections from the Engine board to the HVPS.

Error 44 Defective font card installed in font slot. I have this same error message when plugged into a 100mb hub. It will take you to a list of known fixes and the \% of the time that they fix the problem. Lexmark Error Codes Problem Error 939 RIP Communications Lost Controller Engine Communications Lost The controller board and the engine board cannot communicate with one another.

Error 37 37 Insufficient Collation Memory Memory is too full to collate the print job. Only drivers. Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed. http://jvmwriter.org/error-code/lexmark-error-code-e-804.html Works great and certainly solved the problem (as I expected it would). -Alan A.

Also, can I get some instructions on putting in the rollers. The fixes will also link you to the avalible firmware updates. Newer machines display a sub code to indicate which condition applies. Open doors and covers and remove the toner cartridge.

Change the contents of the old list and save it as new. Il ya eu une erreur à l'application. The pin should enter the tower on the HVPS and depress the cover switch. We do not sell these spare parts.We help you to create your parts sheets to request from your suppliers.

Fuser Pricing How did we do? de Wir entschuldigen uns für die Unannehmlichkeiten. John D. Note: This error indicates the printer was able to read the cartridge ID, but the ID did not pass the verification test.

Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22. Privacy Policy Terms of Use PrintCopy .infoservice Service manual Parts List Error Code Equivalency Sign In Contacts About Us Service manual Error Code Parts List Equivalency Complete information for maintenance If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact. Il ya eu une erreur à l'application.