Home > Error Code > Lexmark Laser Error Code

Lexmark Laser Error Code

Contents

May require service technician Press "GO" to clear message and temporarily continue Install Transfer Drum Unit Error 88 Toner Low Toner sensor detects low toner. John D. The product was delivered just a few minutes ago. Load correct size Error 28 Input sensor not made after pick attempt. http://jvmwriter.org/error-code/laser-printer-error-code.html

Check Toner Sensor Check Cable Check System Board Check developer drive for worn, loose or broken parts. Shop for Lexmark print cartridges Error 32 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer. Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 924 924 Fuser Error - Open circuit detected in thermistor circuit. It can also be the LVPS (low voltage power supply) or a fuse in the power supply on some models.

Lexmark Printer Error Messages

Error 920 920 Fuser Error Fuser is below temperature while printing. See “Duplex” on page 2-16 Error 24 The defined paper size is too short to print data as formatted. Try opening Tray X.

Check the continuity of the fuser lamp at the two heavy leads. Reconnect. Reconnect. Lexmark Printer Error Lights Error 901 Engine Flash Indicates the Flash with the system code program is defective Replace System Board Request Quote Error 914 DC Pick Motor - No Encoder Feedback Check the

The transfer roller is included in the maintenance kit. Lexmark Printer Error Codes Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers Error 26 Duplex unit is installed but paper tray is not sensed. http://www.arbikas.com/view/storage/service/lex_errors.html We can email further info if needed for your particular model.

I am new to this and do not want to screw this up. Lexmark Printer Error Code Ec5 Replace the disk if instructed by the operator panel. Printer and Ink Networking Printers Printer Accessories and Applications Printer Downloads and Applications Printer Ink Cartridge Videos Printer Maintenance Printer Manufacturers Printer Paper Printer Reset Methods Printer Tips and Tricks Printer, If one of these errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace

Lexmark Printer Error Codes

If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. http://support.lexmark.com/index?page=content&id=SO6867 Check AC power source for noise. Lexmark Printer Error Messages Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed. Lexmark Engine Error Thank you for the speedy shipment and response.

Lexmark began as a division of IBM but became Lexmark International in 1991. http://jvmwriter.org/error-code/laser-error-codes.html Error 939 RIP Communications Lost Controller Engine Communications Lost The controller board and the engine board cannot communicate with one another. Replace Printhead Pricing Error 932 Lost hsync No High voltage signal - check connections at both ends of cable for corrosion or oxidation. Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. Lexmark Error Codes Problem

In general, fuser errors require replacement of the fuser as a cost effective repair. Additional info on X and XX codes available by email. If the error appeared while sending a job from the host to the printer, turn the printer off, then turn it on and try again. check over here Error 80 Network Card Codes These user codes are documented in various network card user manuals.

Install more memory Simplify print job Delete fonts, macros and other data stored in RAM Error 39 Page too complex to print.To verify that the printer recognizes all the installed memory, 938.06 Service System Electronics Please try the request again. The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up.

Lexmark Laser printer Error Messages 10 Cover Open This means that the printer is open or no EP cartridge. 20 Paper Jam There was a paper jam in the input area

Replace Printhead Pricing Error 934 Printhhead Error - Lost Lock condition Indicates a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system Error 62 Disk Full Not enough disk space for data that has been requested to be written to disk. Error 931 Printhead error - No first sync Error 932 Lost hsync Replace Printhead Error 934 Printhhead Error - Lost Lock condition Replace Printhead Error 935 Printhead Lexmark Crc Failed Do Not Power Off Thank you and your firm again, you were terrific.

Newer machines display a sub code to indicate which condition applies. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Replace with the correct printhead. this content Check the operation of the toner sensor.

test). Replace the Autocompensator Assy. If an open circuit, replace the lamp or fuser. Replace Printhead Pricing Error 935 Printhead Error - May have sub-codes.

Error 936/937 Main Drive Motor, Transport Motor An error with the main drive motor has been sensed by the printer Optra s 2450 Optra s 1250 Optra s 1650 Optra s Error 922 Fuser failed to reach standby temperature. See “Network Wrap Tests” on page 23. Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed.

Replace the transfer roller as necessary. Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed.