Home > Error Code > Lexmark Error Codes

Lexmark Error Codes

Contents

Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. Error 38 38 Memory Full Memory used to store pages is full. Make sure fuse is installed correctly, Verfy proper fuser is being used. Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the down position if applicable to your machine. weblink

Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Manuals Brands Lexmark Manuals Printer T650 Service manual Lexmark T650 Service Manual: Error Code Table 1; Error Code Table Service Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. POR several times Check each board for secure ground. Roller is approximately 2" in circumference print defects with this repetitive spacing can be caused by transfer roller problems, on a standard 11" page defect would repeat five times.

Lexmark Printer Error Code Ec5

The pin should enter the tower on the HVPS and depress the cover switch. If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact. See “Network Wrap Tests” on page 23. Make sure fuse is installed correctly, Verfy proper fuser is being used.

May be due to the paper feeding manually while motors running and previous page in path. Check AC power source for noise. The fuser can usually be removed with two simple screws and the entire assembly lifted out. Lexmark Printer Error Lights Error 38 Memory Full Memory used to store pages is full.

If there is no continuity, make sure the HVPS contact returns to its upward limit. Lexmark Printer Error Messages Error 939 RIP Communications Lost Controller Engine Communications Lost The controller board and the engine board cannot communicate with one another. See "Sensor (input) early jam service check" on page 2-133. Jump to error 92X Some Lexmark printers have indicator lights which indicate by solid, blinking or off, an error condition.

Check AC power source for noise. 938.06 Service System Electronics Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Replace Printhead Pricing Error 934 Printhhead Error - Lost Lock condition Indicates a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system Error 922 Fuser failed to reach standby temperature.

Lexmark Printer Error Messages

eCommerce Solution : k-eCommerce 3567 Benton Street, Suite 243 Santa Clara, CA 95051 800.360.1337 408.745.9800 Order Desk: 8 AM to 5 PM Home Contact Us About Us Terms of Sale Feedback http://www.castleink.com/category/157/Lexmark-Error-Codes.html If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages. Lexmark Printer Error Code Ec5 Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Lexmark Engine Error They have no affiliation with nor offer any endorsement of the services and products provided by CastleInk.com.

Go to sensor (input) service check. http://jvmwriter.org/error-code/lexmark-x340-error-codes.html See “Duplex” on page 2-16 Error 24 The defined paper size is too short to print data as formatted. Error 7X Network Card Codes These user codes are documented in various network card user manuals. Error 920 Fuser Error Fuser is below temperature while printing. Lexmark Error Codes Problem

Use saved Parts Lists as templates to create new lists. Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers Requires further measurement The printhead (laser scanner) does not contain any serviceable parts. check over here ERROR 23 Jam at the duplex unit.

Go to sensor (input) early jam service check. Lexmark Ms310dn Error Codes To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page. The main motor is located just to the left of the toner cartridge.

Requires further measurement The printhead (laser scanner) does not contain any serviceable parts.

Can be system board or printhead. Error 920.X and 922.XX may display for a cold fuser. Verify correct cable connections from the Engine board to the HVPS. Lexmark Crc Failed Do Not Power Off Run the Quick Disk Test.

To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page. Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed. Error 53 Unformatted or Defective Flash Flash problem at POR or while attempting to write. this content Error 80 Printer has reached 200,000 prints without maintenance count reset.

Replace Printhead Pricing Error 931 Printhead error - No first sync - check connections at both ends of cable for corrosion or oxidation. Check connections to the to interconnect card assembly. Make sure the memory shown on the printout matches the installed memory. Interconnect Board Error 940-943 Color Machines Toner Metering Cycle failure CMKY cartridge 940 = Cyan cartridge 941 = Magenta cartridge 942 = Yellow cartridge 943 = Black cartridge Toner metering cycle

If one of these errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace Fan the media and check for obstructions. 2. Error 27 Envelopes/paper loaded are wrong size. If the paper is not jammed in the duplex unit, then it may be jammed in the rear of the printer.

What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account? Use caution when measuring AC voltages. Error 62 Disk Full Not enough disk space for data that has been requested to be written to disk. Thank you and your firm again, you were terrific.

Make sure top access door is closed securely 2. Controller Board 2. Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed.

If an open circuit, replace the lamp or fuser.