Home > Error Code > Lexmark Error Code

Lexmark Error Code

Contents

Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed. If one of these errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace John D. We got it this morning and I have it installed. http://jvmwriter.org/error-code/lexmark-error-code-e-804.html

test). Error 43 Font card format not supported by printer. A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers https://www.marketpoint.com/lexmark-error-codes.aspx

Lexmark Printer Error Messages

Observe the lamp through the left near side of the printer. Check the continuity of the fuser lamp at the two heavy leads. Replace low voltage power supply assembly.

Error 921 Fuser is below standby temperature when idle. Check the wiring harness cable. Also, can I get some instructions on putting in the rollers. Lexmark Fax Error Codes Roller is approximately 2" in circumference print defects with this repetitive spacing can be caused by transfer roller problems, on a standard 11" page defect would repeat five times.

Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults. Lexmark Printer Error Code Ec5 San Rafael, CA Great that you have that part in stock and thank you for your quick reply. Transfer Roll Error Cannot start servo operation. http://support.lexmark.com/index?page=content&id=SO6393 Replace the bump alignment motor Replace bump motor Replace interlock switch Replace System Card Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex

If an open circuit, replace the lamp or fuser. Lexmark Printer Error Lights Error 82 Photo Developer Cartridge Exhausted The Photo Develper (OPC belt cartridge) has reached the end of it's life and must be replaced. Error 939 RIP Communications Lost Controller Engine Communications Lost The controller board and the engine board cannot communicate with one another. Check LVPS cable for continuity.

Lexmark Printer Error Code Ec5

Thank you for the speedy shipment and response. Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is Lexmark Printer Error Messages The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up. Lexmark Error Codes Problem Reconnect.

Lexmark Fuser Pricing Error 925 A 925 service error indicates the wrong fuser lamp is installed in the printer and does not match the one stored in the printer code. have a peek at these guys Replace the assys in the following order 1. It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer. Error 27 Envelopes/paper loaded are wrong size. Lexmark Engine Error

If the Quick Disk Test passes but the disk does not work, run the Disk Test/Clean (2 hr. Also, if the accumulated sheets are removed, the portion of the job printed after the jam will not be stapled. May be due to the paper feeding manually while motors running and previous page in path. check over here Check for 24V at red wire on interlock switch with door closed 4.

Request Quote Error 920 920 Fuser Error indicates the Fuser is below temperature while printing. Lexmark Ms310dn Error Codes Use caution when measuring AC voltages. If you have other tech support questions that are not covered here, send email to [email protected]

Replace Printhead Pricing Error 931 Printhead error - No first sync - check connections at both ends of cable for corrosion or oxidation.

Paper not being picked up check paper tray & pickup rollers Replace rollers if worn smooth or cracked ERROR 21 The exit sensor was not made in time after the input Replace the Autocompensator Assy. Make sure top access door is closed securely 2. 938.06 Service System Electronics Error 47 47 Font Card Removed While Printing Printer needs data on removed card.

Open the printer rear door to access the jam. Remove the duplex front cover to access the jam area. If the error appeared while sending a job from the host to the printer, turn the printer off, then turn it on and try again. http://jvmwriter.org/error-code/lexmark-x2690-error-code.html Works great and certainly solved the problem (as I expected it would). -Alan A.

Check fan connector and cable for loose or damaged connection. Reload the paper and do a power on reset. I will have purchasing call in an order. Thank you and your firm again, you were terrific.

The transfer roller is included in the maintenance kit. See “Network Wrap Tests” on page 23. Verify correct cable connections from the Engine board to the HVPS. Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected.

Request Quote 947 Engine Board Engine board failure Replace the Engine Board Request Quote 953-954 NVRAM Failure NVRAM Failure 953: NVRAM Chip Failure 954: NVRAM CRC Failure Optra T 640/642/644 If not present check in printer.