Home > Error Code > Lexmark C770 Error Codes

Lexmark C770 Error Codes

Contents

Verify latch relay is operating - slowly close door and listen for interlock switch 3. Lexmark C770 Manual All contents © copyright 2009 - 2016, ManualOwl.com Trademarks and brands are the property of their respective owners. Measure the voltage on connector J17-6 on the system board. How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. check over here

Go to step 4 Install the lamp correctly. Unable to find zero crossover point-Replace the LVPS. If an open circuit, replace the lamp or fuser. Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed. http://support.lexmark.com/index?page=content&id=SO4157&actp=LIST_RECENT

Lexmark Error Codes

Error 921 Fuser is below standby temperature when idle. Paper not being picked up check paper tray & pickup rollers Replace rollers if worn smooth or cracked ERROR 21 The exit sensor was not made in time after the input The fuser can usually be removed with two simple screws and the entire assembly lifted out.

Error 7X Network Card Codes These user codes are documented in various network card user manuals. Cyan TMC switch failure-Go to "940.xx error code service check" on page 2-56. If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact. Lexmark Engine Error Sign up!

Registration (staging) motor error—replace the registration motors. Lexmark C782 Service Manual Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Manuals Brands Lexmark Manuals Printer C77X Service manual Lexmark C77x Service Manual Page 50 Hide thumbs Also See for C77x Error 25 Input sensor made at wrong time. It may be necessary to remove the re drive assembly to observe the lamp cycling on and off.

Reconnect. Lexmark Dc Pick Motor The fuser, melts or fuses the toner to the media and has a heat roller and a pressure roller. Industries Worked In Adjustable Bed Bases Audio-Visual / Home Theater Automated Teller Machine (ATM) Carpentry / Fixture Install CCTV / Alarm Systems Desktop/Laptop General Tasks Kiosk Low Voltage Cabling Networking Point See "ITU assembly removal" on page 4-49.

Lexmark C782 Service Manual

Home | My Manuals | Manual Index | Manual Categories | About Us | Contact Us | Privacy Не удалось открыть файл, поскольку в вашем браузере отключено использование JavaScript. Включите его RAM soldered on board is bad. Lexmark Error Codes Remove the duplex front cover to access the jam area. Lexmark Printer Error Messages Engine Board 3.

What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account? check my blog Or should I take the printer to a repair shop? If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages. Pay close attention to the area where the toner cartridge sits. Service Error 146.00 Dc Pick Motor

Error 80 Network Card Codes These user codes are documented in various network card user manuals. Replace that part with a new FRU. See "System board removal" on page 4-89. 4 Reinstall the fuser assembly. this content All rights reserved.

characters left: Contact Us|Terms of Service|Privacy & Security|About Us|Our Network © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 125 7892546 By using our site, you agree to our use of cookies. Lexmark Error Codes Problem 3567 Benton Street, Suite 243 Santa Clara, CA 95051 800.360.1337 408.745.9800 Order Desk: 8 AM to 5 PM Home Contact Us About Us Terms of Sale Feedback FAQ Digital Media Replace the Autocompensator Assy.

Replace defective cartridge.

Go to "956.xx service error service check" on page 2-64. See removal" on page 4-89. My LC keeps reprinting a document that a printed this a.m. 10/18/2016 10/18/2016 Viet - Printer Tech X Ask a Technician Get a Professional Answer. 100% Satisfaction Guaranteed. 29 Technicians are Lexmark Printer Error Code Ec5 Install more memory Simplify print job Delete fonts, macros and other data stored in RAM Error 39 Page too complex to print.To verify that the printer recognizes all the installed memory,

Black TMC switch failure-Go to "943.xx error code service check" on page 2-62. If one of these errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace Ant idea of cost to repair? have a peek at these guys The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up.

See removal" on page 4-89. Watch to see if the lamps turn on and off as the lamp heats up. Error 920.X and 922.XX may display for a cold fuser. Is the voltage correct?

replied5 years ago. If you have other tech support questions that are not covered here, send email to [email protected] Remove jammed media Error 90X Software Error Unrecoverable software error. Make sure top access door is closed securely 2.

Los Altos Hills, CA Thank you.