Home > Error Code > Lexmark 632 Error Codes

Lexmark 632 Error Codes

Contents

We got it this morning and I have it installed. Error 921 Fuser is below standby temperature when idle. C'è stato un errore con l'applicazione. Generated Thu, 20 Oct 2016 06:49:25 GMT by s_wx1157 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection weblink

Any help here would be appreciated too. It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer. Es gab einen Fehler bei der Anwendung. Can be system board or printhead. http://www.all-laser.com/aerrorlex/

Lexmark Error Codes

Powered by WebJaguar B2B E-Commerce & B2C E-Commerce Solution by Advanced EMedia ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the Remove toner cartridge for better access to jammed paper. I am new to this and do not want to screw this up.

Note: This error indicates the printer was able to read the cartridge ID, but the ID did not pass the verification test. Thank you and your firm again, you were terrific. Additional info on X and XX codes available by email. Lexmark Crc Failed Do Not Power Off Make sure the memory shown on the printout matches the installed memory.

Replace Printhead Pricing Error 936 Error 937 Error 936/937 Main Drive Motor, Transport Motor An error with the main drive motor has been sensed by the printer Optra s 2450 Optra Lexmark Printer Error Messages Error 47 47 Font Card Removed While Printing Printer needs data on removed card. Verify latch relay is operating - slowly close door and listen for interlock switch 3. http://support.lexmark.com/index?productCode=LEXMARK_T630&segment=SUPPORTproductCode%3D&page=content&id=SO2206&locale=EN&userlocale=EN_US We sell only remanufactured ink and compatible cartridges for Dell, HP, Canon, Epson and Lexmark printers.

Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22. Lexmark Printer Error Code Ec5 C'è stato un errore con l'applicazione. Can't find your code? ERROR 22 The exit sensor was not unmade in time.

Lexmark Printer Error Messages

Error 80 Network Card Codes These user codes are documented in various network card user manuals. Works great and certainly solved the problem (as I expected it would). -Alan A. Lexmark Error Codes May be due to the paper feeding manually while motors running and previous page in path. Lexmark Engine Error Replace Printhead Pricing Error 931 Printhead error - No first sync - check connections at both ends of cable for corrosion or oxidation.

The main motor assembly may need to be replaced. http://jvmwriter.org/error-code/lexmark-x340-error-codes.html Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed. It can also be the LVPS (low voltage power supply) or a fuse in the power supply on some models. Press "GO" to clear message and temporarily continue Install OPC Belt/Photo Developer Error 84 Transfer Drum Exhausted The Transfer drum has reached the end of it's life and must be Lexmark Error Codes Problem

Check paper sensor flag for restricted movement or damage. Error 930 The wrong printhead is installed. Es gab einen Fehler bei der Anwendung. check over here Install more memory Simplify print job Delete fonts, macros and other data stored in RAM Error 39 Page too complex to print.To verify that the printer recognizes all the installed memory,

Google *We sell remanufactured and compatible cartridges for Epson printers - no OEM Epson inkjet cartridges are sold. Lexmark Printer Error Lights The system returned: (22) Invalid argument The remote host or network may be down. If an open circuit, replace the lamp or fuser.

John D.

Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults. Check the toner metering cam on back of suspect cartridge. Shop for Lexmark print cartridges Error 32 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer. 938.06 Service System Electronics Replace the assys in the following order 1.

We use brand names and model distinctions for non-OEM cartridges for the sole purpose of attesting printer compatibility. Error 939 RIP Communications Lost Controller Engine Communications Lost The controller board and the engine board cannot communicate with one another. See “Network Wrap Tests” on page 23. this content It may be necessary to remove the re drive assembly to observe the lamp cycling on and off.

Replace the transfer roller as necessary. Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. Check LVPS cable for continuity. Controller Board 2.

Error 920.X and 922.XX may display for a cold fuser. May require service technician Press "GO" to clear message and temporarily continue Install Transfer Drum Unit Error 88 Toner Low Toner sensor detects low toner. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Error 63 Unformatted or Defective Disk The printer will ignore a disk it senses as defective.

POR several times Check each board for secure ground. Check printhead, cable, motor, system board. The fuser is the main part of a printer maintenance kit. Open doors and covers and remove the toner cartridge.

Replace the bump alignment motor Replace bump motor Replace interlock switch Replace System Card Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex es Lamentamos las molestias. Remove and reinstall print cartridge. Replacement of the thermistor is not a cost effective repair, replace fuser assembly.

To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page. If the error appeared while sending a job from the host to the printer, turn the printer off, then turn it on and try again. Error 27 Envelopes/paper loaded are wrong size. The pin should enter the tower on the HVPS and depress the cover switch.