Home > Error Code > Laxmark Error Code List

Laxmark Error Code List

Contents

Also, can I get some instructions on putting in the rollers. Check fan for binding or defective bearing - Replace Fan How did we do? See "Sensor (input) service check" on page 2-126. 1. If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages. navigate here

See “Network Wrap Tests” on page 23. The product was delivered just a few minutes ago. Please try the request again. Es gab einen Fehler bei der Anwendung. Check This Out

Lexmark Printer Error Messages

Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Verify latch relay is operating - slowly close door and listen for interlock switch 3. Error 122 Fuser Error - Problem in the fuser, not heating, heating to quickly or too hot.

Replace the assys in the following order 1. See "Sensor (input) late jam service check." on page 2-129. 1. Send an Email Toll Free: 877-365-1903 About us Terms Contact us Help Login Brand : All brands HP Models Lexmark Models Xerox Models Model : Choose a brand Lexmark Printer Error Lights Replace low voltage power supply assembly.

fr Nous sommes désolés pour ce désagrément. Lexmark Printer Error Code Ec5 The printer is set for (hardware or software) Defective D-roller Debris in the paper path Gears not turning or broken gear Defective paper tray Broken input sensor flag Defective input sensor Verify correct cable connections from the Engine board to the HVPS. http://www.castleink.com/category/157/Lexmark-Error-Codes.html The sensor (input) rebounded once the trailing edge of the media passed.

Shop for Lexmark Maintenance kits * This is a model dependent interval Install maintenance kit and reset maintenance message Purchase Lexmark maintenance kits How did we do? Lexmark Fax Error Codes Google *We sell remanufactured and compatible cartridges for Epson printers - no OEM Epson inkjet cartridges are sold. Cycle power Defective font card Defective system board 44 Font Card Error See 43 45 Downloaded Font Error Software setup Software drivers System board 46 Download Character Error See 45 47 Greenlawn, NY 11740 Tel:800-399-5193

Privacy| Security | Terms| Cambiar a Espanol | Site Map | Printer Ink Brands Please Note: Xerox, Lexmark, IBM, HP, Epson, Canon, Apple and other

Lexmark Printer Error Code Ec5

Error 52 Flash Full - Not enough flash memory for data requested to be stored. http://support.lexmark.com/index?page=content&id=SO4438&userlocale=EN_US&segment=SUPPORT&productCode= Error 80 Printer has reached 200,000-300,000* prints without maintenance count reset. Lexmark Printer Error Messages See "Sensor (input) early jam service check" on page 2-133. Lexmark Error Codes Problem The media reached the sensor (input) but did not clear it within the specified time.

Replace the transfer roller as necessary. check over here Replace defective cartridge. May require service technician Press "GO" to clear message and temporarily continue Install Transfer Drum Unit Error 88 Toner Low Toner sensor detects low toner. The fuser, melts or fuses the toner to the media and has a heat roller and a pressure roller. Lexmark Engine Error

Error 920.X and 922.XX may display for a cold fuser. The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up. Error 7X Network Card Codes These user codes are documented in various network card user manuals. his comment is here Error 26 Duplex unit is installed but paper tray is not sensed.

The media reaches the sensor (input) sooner than the specified time. 938.06 Service System Electronics If the error appeared while sending a job from the host to the printer, turn the printer off, then turn it on and try again. San Rafael, CA Great that you have that part in stock and thank you for your quick reply.

It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer.

Also, if the accumulated sheets are removed, the portion of the job printed after the jam will not be stapled. Error 921 Fuser is below standby temperature when idle. Error 44 Defective font card installed in font slot. Lexmark Ms310dn Error Codes Make sure the memory shown on the printout matches the installed memory.

Fan the media and ensure it is properly installed. 2. test). Engine Board 3. weblink Perform fuser service check.

If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed. The transfer roller is included in the maintenance kit. Reload the paper and do a power on reset. Go to sensor (input) lingering jam service check. "Sensor (input) lingering See jam service check." on page 2-132. 1.

Error 80 Network Card Codes These user codes are documented in various network card user manuals. C'è stato un errore con l'applicazione. Load correct size Error 28 Input sensor not made after pick attempt. Service errors 980 thru 984 < device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. >