Home > Error Code > Laserjet Iiip Error Messages

Laserjet Iiip Error Messages

Contents

II, IID, III, IIID Replace paper control PCB. Tractor feed paper with the edges ripped off doesn't seem to work very well. Holzarbeiten Das intelligente Haus Nützliches Zubehör Links HP9810A HP97 Siemens comfoset 150 Detartrage Impressum

Repairing the HP LaserJet Series II power supply My HP LaserJet Series II In May 2009, Replace if defective An abnormal connection break may have occurred during data transfer - Press Continue or Go to clear this error message. this contact form

If not replace the motor or drive circuit as required. This board contains the famous C154 capacitor, which can be seen on the picture (the green cylinder). Moe is correct that the "50" is usually casued by the AC Mod. Document the error message. http://fixyourownprinter.com/posts/24948

Hp Printer Error Codes List

Los Altos Hills, CA Thank you. HP IIP, 12 OPEN OR NO EP --and-- 50 NEEDS SERVICE errors 11. Remove the card and reseat it, try swapping with a know good card from another printer. In my case, however, if the printer was turned on 20 minutes after the error occurred, it completed its self test.

Sharepoint Developer required Rate-$45/hr or best --Client -Cogizant-Microsoft 5. Underneath a printed circuit board can be seen, which is held in place with two black screws. Back back to top How did we do? Hp Printer Error Code List Pdf May need to reload your PostScript print driver file.

ERROR 67 - Defective formatter PCA 2686A/D, II, IID, IIP,III,IIID,IIIP,4,4+,4P - Defective formatter board, try reseating the connectors and any accessories you may have plugged in On the 4Si this could Hp Laptop Error Codes Turn the printer off and then back on. Watch the termination's on the network cabling. http://www.all-laser.com/aerror-code/ No toner cartridge.

Laser printers are page printers and require the entire page to be processed before beginning to print. Hp Error Code Oxc4eb827f If you hear the motor spin but not stabilize and you get an error 52 the scanner motor is most likely defective. If the lamp is discolored it's developed a leak at the glass to ceramic seal and the filament has oxidized and is burned out. Most times this can simply be reinstalled.

Hp Laptop Error Codes

Wrong length paper or incorrect S/W paper size selected. The chip may be missing or defective or contain incorrect information. Hp Printer Error Codes List Bad paper exit sensor. Hp Computer Error Codes You will see "00 SMODE" in the display, then "05 WARM UP" and finally the page count will be displayed.

Some of the checkpoints referred to in this document require special tools or meters as well as familiarity and training on laser printers. weblink May also be formatter. Power cycle the printer by unplugging from the power source. The error 10 indicates a problem with the printer obtaining the information from this chip. Hp Inkjet Printer Error Codes

Verify that the tabs aren't damaged and that the tray switches located in the printer are not damaged. See the single tyristor on the power supply module.Good luck to all! It can also be caused by a defective DC controller. navigate here Check and reinstall ERROR 79 - Software Drivers, Memory PCA's, Font Macro Cartridges, I/O Cards, Def.

There are no similarities, save both are laserprinters and built by Hewlett-Packard. Hp Officejet Error Codes Power cycle the printer by unplugging from the power source. Again, power down for 10-15 minutes or more to see if the error resets.

Then put the printer back online and send a test job from the host computer via the parallel cable.

Bad paper input (paper out) sensor Paper cassettes not properly loaded Bad solenoid operation Bad gear(s) or gears not meshing in drive train Bad main motor or drive circuit Bad delivery If the problem persists and is application specific, verify proper setup with application vendor. Look for the conductive contacts on the cartridge and the corresponding contacts in the printer and make sure they are clean and free of contaminants. Hp Printer Error Code 0x610000f6 To observe the lamp, you must first remove the fuser assembly from the printer.

Contact your dealer or HP Service Technician. 53 Error LaserJet, Plus, 500 plusIndicates an internal service malfunction. Back back to top How did we do? There can be a number of reasons, the most obvious being a burnt out fuser lamp. his comment is here Locate and verify a stable power source.There is an internal service error.

This requires removal of the cover, an unpleasant task, and measurement of the fuser terminals. Firmware updates are available for some machines at http://hp.com and clicking on the drivers and software tab. Removal of the lamp, although not difficult, requires knowing where the snaps are located to remove the plastic covers. Press front panel button to see secondary indicator pattern.

ERROR 43 / ERROR 43 OPT INTERFACE This indicates a communication problem between the formatter PCA and an optional interface installed (such as a network card). Verify that the SIMMS or memory cards are seated. Is the software set for the size you're using? Simplify the print job by removing font changes and/or graphics.

If message clears, then the problem exists with the expanded memory. 63.1 Error63.2 Error63.3 Error63.4 ErrorIIISiIndicates a possible faulty expansion SIMM. Reseat the card and if available, swap with a known working card. Check connections to DC controller - replace main motor 4L/4 Main motor problem, check gear train for binding. You may need additional memory. 4L Same thing with to much data or the page is to complex.