Home > Error Code > Laserjet Iii Error Codes

Laserjet Iii Error Codes

Contents

What to do:If you have an older model then reseating or changing the memory may resolve the issue. What to do:These faults typically needed assistance from an experienced HP engineer. If the firmware should become corrupted or fail (usually because of an interruption when attempting to update the firmware), the product will no longer function. Defective High Voltage power supply or on the LJ II/III the DC controller to High Voltage power supply can be defective. this contact form

If the first four lights, top to bottom, are lit, press and hold the GO and RESET buttons. Can also be DC controller. 5Si/4+/4Si/IIISi (X=2, 3 or 4) Fan motor faulty, check fan number X or duplexor fan and replace as necessary 5 Main motor failure - replace main Look for bits of paper lodged in the path particularly around the sensors. 4L/4P printers can have paper stuck in the pickup area which is accessed by removing the screw over If your machine uses a paper separation pad, a small rubber or cork material pad check for a smooth surface without any friction.

Hp Printer Error Codes List

Sudden occurances are almost always the fuser assembly. A common solution is to tighten the connectors at both the scanner assembly and the DC controller. First Time Here? Then put the printer back online and send a test job from the host computer via the parallel cable.

Reset as needed. You can remedy this by replacing the paper guide plate assembly, RG5-248-030. The printer has detected the wrong fuser. 50.6 Open fuser. Hp Error Code Oxc4eb827f What to do:Try one or more of the following, depending upon your HP printer:
1.

That could be a number of things like the LaserJet losing network connectivity or by the "part not found" section of that error it could be something as simple as the Hp Laptop Error Codes I believe he has a kit on this site. Incorrect cable hookup or bad I/O port in computer. Back back to top How did we do?

This may clear the error - either temporarily or permanently. Hp Printer Error Code List Pdf http://fixyourownprinter.com/fusersx.html by moe on Nov 22, 2004 at 2:42pm Add comment Please sign in to comment According to the error lists error 50 can mean a bad AC power supply or SHIFT+CONTINUE to continue printing Temporary error. Replace optional I/O card. 43 OPT INTERFACE 1.

Hp Laptop Error Codes

Call Toll Free (800) 551-1943 | OPEN M-F 8:30-4:00PM CST | Order Online Anytime! click here now Bad paper exit sensor. Hp Printer Error Codes List Dirty or obstructed paper path. Hp Computer Error Codes General information with more detailed information available.

Paper path rollers worn? weblink Defective Paper Control Sensor PCB - These do fail and will need to be replaced. Some of the supported Lexmark Machines are: Lexmark 4039, Lexmark 4040, Lexmark 4046, Lexmark 4049, Lexmark 4059, Lexmark 4060, Lexmark 4069, Lexmark 4520, Lexmark 5040, Lexmark 5050, Lexmark T610, Lexmark T612, Plug the printer into a wall outlet and see if this resolves the problem. 2 If the printer is already plugged into a wall outlet, try another power source in the Hp Inkjet Printer Error Codes

Back back to top How did we do? Replace font cartridge. 2. Then put the printer back online and send a test job from the host computer via the parallel cable. navigate here Try another cable and make sure the computer is turned on and the cable is fully inserted at both ends.

How did we do? Hp Printer Error Code 0x610000f6 ERROR 67 Defective formatter PCA On the 4Si this could be a temporary error which can be corrected by cycling the power 4V/4MV - This can also be a temporary error See the single tyristor on the power supply module.Good luck to all!

Bad fan, PS4 or PS5.

Fuser exit sensor flag and sensor 14 No EP cartridge or No toner cartridge. May be feed problem. Replace High-Voltage Power Supply. 20 ERROR/MEM OVERFLOW/INSUFFICIENT MEMORY 1. Hp Officejet Error Codes Visually check or replace toner cartridge. 2.

When the defective part is removed, the board material under the speed control IC is usually burned. This error can begin as an intermittent error which can be corrected by pressing Alt- continue (on HP printers) but it's only a matter of time until you can no longer If the problem continues, remove the optional interface card and set the printer for standard parallel interface by taking off-line and holding down "Menu" key for 5-10 seconds. his comment is here Check PS102 and PS103 13.5 Paper delay jam at fuser.

Reset by pressing the continue key. 2. Error 57 6P/5P/5 Main motor problem, check gear train for binding. PS402 on front door PCA under transfer roller Bad DC controller PCB 16 Toner low All printers Toner uneven in cartridge Bad toner cartridge contact points Replace high voltage power supply. Replace cable, Fuser to DC Controller, connector J206. (P/N RG1-0907-000.) 2.

To observe the lamp, you must first remove the fuser assembly from the printer. What to do:You can normally resolve this by pressing the SELECT button. Fuser heater cut-off. Check pickup rollers and separation pad clean as needed.

No toner cartridge or cartridge not seated. 3. This is the electronic information, or e-label, on the print cartridge.