Home > Error Code > Labview Error Codes

Labview Error Codes

Contents

You can use this property only with the Conditional Disable structure. 1377 A Diagram Disable Structure cannot have conditions. This problem might occur due to a type cast error. 1564 Project file cannot be saved at this time. This file normally is a user data file. 100 File contains erroneous data. The Scan From String function was unable to scan its input because the data was not in the expected format. this contact form

Most likely the VI is broken or one of its subVIs cannot be located. To correct this error and inline the subVI, remove the implicit Property Node or Invoke Node. 1488 The migration file cannot load because it is no longer supported. 1489 The migration You may be experiencing noise on your serial line. These folders can be found at the location found in[National Instruments]\Shared\MIerrorsas shown below. read this article

Labview Visa Error -1073807339

The specified property code is not valid for this refnum. −1967345150 Invalid privilege ID. A file path with the filename is required, but the supplied path is a path to a directory. 118 The supplied folder path does not exist. 122 The resource you are Add Comments 1 2 3 4 5 My Profile|Privacy|Legal|Contact NI© National Instruments Corporation. This normally is a user data file. 99 Incorrect file version.

Another possible cause for this error is there might be a bad network connection. A buffer underflow has occurred because the application is not writing data quickly enough. −4803 The sound driver or card does not support the specified operation. Before assuming that the system needs more memory to complete the operation, make sure the read format you are requesting is valid for the data being read. 1157 You cannot use Labview Error 1073807339 Run the VI.

The 0x08 flag is not useful when performing asynchronous calls. Daqmx Error Codes All rights reserved.| Cart|Help KnowledgeBase Request Supportfrom an engineer NIHome > Support > KnowledgeBase EnglishJapaneseChinese(China)SpanishChinese(Taiwan)German 20 ratings: 3.79 out of 5   Error -1073807246 Using This is usually due to a required driver not being installed on the system. −1073807201 The interface cannot generate an interrupt on the requested level or with the requested statusID value. http://digital.ni.com/public.nsf/allkb/FD9FEFCDD2F95C29862572AA006AC909 For example, this error might occur when a front panel terminal is inside a structure. 1430 The path is empty or relative.

The specified wave format is not supported. Labview Error 200279 Add Comments 1 2 3 4 5 My Profile|Privacy|Legal|Contact NI© National Instruments Corporation. The palette type input is invalid. This error can occur if you use a property or method that is not supported in the LabVIEW Run-Time Engine. 1044 VI is locked. 1045 Null Refnum passed to Close Reference.

Daqmx Error Codes

A format specifier does not match the data type of its corresponding argument in a Format Into String or Scan From String function. 82 Unknown format specifier. over here Verify the values you wired to the Open VI Reference function. 1097 An exception occurred within the external code called by a Call Library Function Node. Labview Visa Error -1073807339 Answered Your Question? Labview Visa Error Codes For example if the input is a path, the path might contain a character not allowed by the OS such as ?

A buffer underflow has occurred because the application is not writing data quickly enough. 4821 Overwrite error. http://jvmwriter.org/error-code/labview-error-code-63040.html You also can generate error cluster reports to obtain descriptions of built-in error codes. The project has a locked untitled dependency. To correct this error, remove either the 0x08 option or the 0x80 and 0x100 options. 1604 The Open VI Reference function does not support using the option 0x08 (Prepare for reentrant Labview Error Daqmx

Sync up changes before attempting this operation. 1500 If you obtain a user event reference in one application instance, you cannot use that user event reference in another application instance. YourFeedback! Parsing error. −1073807341 Invalid access mode. −1073807339 Timeout expired before operation completed. −1073807338 The VISA driver failed to properly close the session or object reference. navigate here To correct this error, ensure the target VI is idle or reentrant.

If this error occurs, you must enable buffering and reopen the file. 1546 The VI must be in a project to use this property. 1548 Queue refnum cannot be obtained with Labview Custom Error Codes Refer to the help for the property or method to determine if it is allowed remotely. 1033 Bad run-time menu file version. 1034 Bad run-time menu file. 1035 Operation is invalid To correct this error, restart LabVIEW and review your code for recursive data structures. 1000 The VI is not in a state compatible with this operation.

The palette type value has enumeration values of Controls or Functions.

Poor|Excellent Yes No Document Quality? You can use the Obtain Queue or Obtain Notifier function to look up a queue or notifier by name. Unnamed mechanisms do not have this restriction, because each request to obtain an unnamed mechanism creates a new mechanism. Labview Fpga Error Code You cannot use user events for communication between LabVIEW application instances. 1502 Cannot save a bad VI without its block diagram. 1503 Cannot save a clone of a reentrant VI. 1504

The input for class name is not correct or is in the wrong format. Add Comments 1 2 3 4 5 My Profile|Privacy|Legal|Contact NI© National Instruments Corporation. Contact the distributor of the file. his comment is here Navigate to the VI for the reference and click the Open button to configure the reference. 1190 The operation is not allowed when the control has key focus. 1191 The wire

The specified wave format is not supported. This mismatch implies that the dependency report is unreliable, so the ReadLinkInfo operation was aborted. 1595 The RT target does not have enough memory to load the startup application. 1596 Cannot A specified refnum was not valid. −1967345151 Invalid property code. In a built application, this error might occur because the VI being loaded was last compiled for a different OS, in which case you must save the VI on the current

There is a size mismatch between the data in the reference and the data wired to the Data Value Reference Write Element border node. 1586 Compiled code is out of date. You may have a bad serial cable.Try another serial cable. 5. For example, VI Server:Generic:GObject 1312 Structure frame index is out of range. When a Boolean control is configured with a latching mechanical action, the Value property always returns an error.

A buffer underflow has occurred because the application is not writing data quickly enough. −4803 The sound driver or card does not support the specified operation. The following are the possible causes as well as the solutions to these errors: Another program has control over the serial port. Related Links: KnowledgeBase 41Q6FHS9: LabVIEW Error Code File LocationsLabVIEW 2014 Help: Ranges of LabVIEW Error CodesLabVIEW 2014 Help: General LabVIEW Error Codes LabVIEW 2014 Help: Defining Custom Error Codes Attachments: generate Possible reasons include an invalid path or lack of access rights. −1073807198 An error occurred while performing I/O on the specified file. −1073807197 One of the specified lines, trigSrc or trigDest,

You must specify a different location on disk when copying a project library. 1440 The filename does not match the expected name. YourFeedback!