Home > Error Code > Kohler Error Code 62

Kohler Error Code 62

Contents

Sign In Sign In Remember me Not recommended on shared computers Sign in anonymously Sign In Forgot your password? J150exeis will be running along and 10/18/2016 10/18/2016 oldnewenglandmarine Tan I have a 1993 150 hp evinrude which runs low on fuel 10/18/2016 10/18/2016 jacksparrow1956 I have a Fortex 101 Thrust Reattached and started generator but it cut off after about 8 seconds.I directly attached a fresh water hose to the raw water feed line after the sea strainer before the impeller, If continues running, a flow restriction in the fuel pump/cooler block needs attention but if genset again shuts down with an EC62 error I'm stuck. http://jvmwriter.org/error-code/lg-error-code-oe.html

I dont think there is uch to be able to change since some of the gas lines run through metal tubing tight close to the carb intakes. If you find a hot spot, either move the fuel line or make up a heat shield and see if this works Just a thought.. Cboy7, Sep 29, 2009 #1 Oldtimer LawnSite Bronze Member from Pensacola, Florida Posts: 1,458 Has the dealer used a computer to diagnose the problem? Ulf,you will need to disconnect the battery from the unit to clear the code after you replace/check the impeller.I assume you did clean out the sea water strainer.Scott Ask Your Own navigate to this website

Kohler Generator Error Codes

Code 34 could be a bunch of things. Hope u found a solution. I noticed poor water flow from the exhaust. Do I need a new starter? ...engage the flywheel.

The Question: I was told the flow of seawater through the heat exchanger can't exceed 2 psi. Since JustAsk prohibits direct contact, I'll send it to you via JustAsk's webmaster if desired. Started generator but it cut off after about 8 seconds.Removed the impeller finding the half half moon drive opening split but intact. Discharge water flows like a garden hose.

If so my next step would be to replace the Seawater Pressure Switch.Or should I check the Seawater Pressure Switch with amulti meter first and if so what readings am I I'm over on Mattox Creek at Harbor View Marina. Ask a Boat Repair Expert. Take care have a nice 4th!!! -Mark Expert: Hank F.

If the code is correct you might have an impeller issue or a blockage to your gene. 2001 290DA Reply With Quote 07-04-2011,04:39 PM #3 ReLAXin View Profile View Forum Posts Prev12Next » Not finding what you are looking for? Stay logged in Log In / Sign Up RSS feed for LawnSite LawnSite Forums / Equipment / Mechanic and Repair / Certain XenForo add-ons by Waindigo™ ©2011-2012 Waindigo Limited. When it gets hot..

Kohler 5ecd Fault Codes

You need 40psi. http://www.boatered.com/forum/topic.asp?TOPIC_ID=119116 Generated Thu, 20 Oct 2016 05:13:27 GMT by s_wx1126 (squid/3.5.20) Kohler Generator Error Codes By ironbyron in forum Ask a Sea Ray Employee...(No Longer Active) Replies: 0 Last Post: 07-13-2009, 11:07 AM Kohler Generator Error Code, please help By mohandis33 in forum General Maintenance/Repair Questions Kohler Marine Generator Fault Codes Terms and Rules Privacy Policy Forum software by XenForo™ ©2010-2016 XenForo Ltd.

I got this code once and like the others was not listed in the manual. navigate here Disconnect the seawater supply hose at the the heat exchanger and put in a fresh water supply hose to feed fresh water directly through the heat exchanger and out the exhaust. Located and removed. You may call me at XXX-XXX-XXXX or email me directly at [emailprotected] which is [emailprotected] Again appreciate your help & reply.

Is this where you are seeing the EC62 I am assuming? Not sure about the 5E but the 6.5CZ has a fuel filter that attaches directly to electric fuel pump. From what I have read EC62 is Sea Pump Pressure Fault EC62. Check This Out Charles, IL (burbs of Chicago) Boat sea ray Details 290 Sundancer 2001 Engine(s) Twin 5.0 w Bravo 3's Posts 156 Re: Kohler error code 62??

It cranked for an extended period. There are many baffles and what looks like milled openings which didn’t seem blocked. characters left:

Contact Us|Terms of Service|Privacy & Security|About Us|Our Network|Sitemap © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 56 11248934 Login|Contact Us Small Engine Small Engine Troubleshooting Problems?

What can I do to prevent this in the future?

Please try the request again. Any ideas on what's going on and suggested solutions? Perhaps he will see your post and offer some advise.If you need his info, let me know.Jamie Homeport: Rockville, MD / Colonial Beach, VA CurrentSea RO#10265 Posted-Sep 03 2008: Margaret Thatcher Homeport: Lake Lanier, GA Wishoot RO#22990 Posted-Sep 03 2008: 18:04:25 Had the exact problem with the exact model.

Run genset leaving the fuel pump/cooler to discharge the raw sea water into the bilge so there is some cooling to the fuel pump. Searched on line finding the code to be "Sea Plump Pressure Fault".I clean the sea strainer which wasn’t plugged nor did it contain foreign material. you beat me to the post. this contact form Sign Up All Content All Content This Topic This Forum Advanced Search Browse Forums Gallery Calendar Staff Online Users More Activity All Activity Search More More More All Activity Home Chaparral

To start viewing messages, select the forum that you want to visit from the selection below. You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. Bob J Homeport: Waretown, NJ gcolton RO#9708 Posted-Sep 04 2008: 12:19:48 Is the oil level all the way to the full line? Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More...

Answer these questions for more details: Does your ... He is also a member here on Boatered.