Home > Error Code > Kitchenaid Oven Error Message

Kitchenaid Oven Error Message

Contents

AppliancePartsPros 24,563 views 3:34 Checking an Oven Temperature Sensor - Duration: 3:58. If the wiring connections and the ground are okay, the control board will probably need to be replaced. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). F5 F5 codes refer to door latch issues. Source

HBT 12,536 views 2:44 Stove-Oven-Range Diagnostic -Display Error-Jenn-Air,Whirlpool,Maytag,-KitchenAid,Roper- JDS9860CDS01 - Duration: 5:06. Often I would come back hours after the error code showed up and press cancel and then it would work instead of doing nothing and go back to showing the time, F07 - Motor Control Unit (MCU) Error - Unplug unit and disconnect power to check wire harness connections between drive motor and MCU, and between MCU and Central Control Unit (CCU). If error continues, replace electronic control (control board) and if error still persists, replace the touch module (touch pad). http://www.partselect.com/JustForFun/Kitchen-Aid-Appliance-Fault-Codes.aspx

Kitchenaid Oven Error Code F2e1

Copyright © 1999-2016 , Eldis Group Partnership. ApplianceVideo.com 15,305 views 5:06 E1 f5 code oven - Duration: 1:51. See Details Whirlpool WOD51EC7AS 27" Electric Double Wall ... Verify that the inlet valve is operational.

Add to Want to watch this again later? Whirlpool Range Error Codes You'll need to replace the oven temperature sensor in order to operate the range's oven capability. Replace is defective. Kitchenaid Oven Error Code F2e1 Stuck Shorted Key Thanks!

Either way, you must replace the oven temperature sensor. Check the door switch/lock for any debris or foreign objects. Gently pull the tab down approximately 1/4 inch or until a 'click' is heard.

Replace failed component.

Check the drive system for any worm or failed components and reconnect power and plug unit in. Kitchenaid Dishwasher Error Codes Check the inlet valve and pressure switch for proper shut off and operation. See Details Kenmore 49609 27" Electric Combination Wall ... All F3-E Codes - Oven Temperature Sensor (RTD) or Warming Drawer Defect - Replace oven temperature sensor (RTD).

Kitchenaid Refrigerator Error Codes

Disconnect power and unplug unit to check wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit. http://www.appliancetimers.com/failure-code-page?manufacturer=ka&type=r F7-E1 - Common Switch Wire Is Defective - This error occurs when common wire to latch switch and door switch is shorted. Kitchenaid Oven Error Code F2e1 E2 - Shorted Temperature Sensor - Replace temperature sensor. Kitchenaid Oven Error Code F6e0 My KitchenAid Oven Will Not Unlock Typically, locking issues result from user error or oven malfunction.

KitchenAid Pro Line Front Loading Gas and Electric Dryer Fault Codes (Models KHEV01RSS and KHGV01RSS) PF - Power Failure - PF error code indicates a power failure during the dryer's cycle. this contact form ft. Select the 'cancel' function and wait 60 seconds. Except it would come up again either immediately or 25-40 min after I start cooking. Kitchenaid Oven Error Code F2e0

Note: This error code will ONLY appears in the diagnostic test mode. KitchenAid Pro Line Front Loading Automatic Washer Fault Codes (Model KHWV01RSS) FH - Detects No Water Entering Machine or Replace failed component. Check resistance of heating element if present in model, for abnormal reading (infinity). have a peek here Replace failed component.

Thanks again! 03-31-07,06:54 AM #8 gdoug Member Join Date Nov 2003 Posts 393 I don't think anything in the cooktop area is connected to the control board. Kitchenaid Oven Error Code F9e0 Check the MCU by looking for operations of the drive motor, and check drive motor for powered rotations. The system returned: (22) Invalid argument The remote host or network may be down.

F13 - Internal CPU checksum Error(s) - Disconnect power for one minute and check to see if error reappears once power has been restore.

If error reappears, replace touch pad, or touch and pad and control board (clock) if all one assembly. Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes. Select the 'cancel' function and wait 60 seconds. Kitchenaid Error Code F8e0 Disconnect power and unplug unit to check wire harness connections to the CCU and the touch pad/LED assembly.

Note: If this error occurs, the door will remain locked and the drain pump will run constantly even if 'cancel' is selected. Note: A power glitch may cause this error. I would first check in the back of your range, behind your back access panel, check all the wiring to see if any wiring is burned or shorted to your metal Check This Out Powered by vBulletin™ Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc.

View our Privacy Policy here. Some exceptions apply.Learn how our pricing differs from other firms. $169 Home About Us Corporate Profile Key Benefits Careers Testimonials Repair Services Why Repair Your Timer? The electric control unit is all one piece and looks like it runs at least $255! F03/F12/F13/F22 The F03, F12, F13 and F22 codes refer to problems within the ERC.

F02 - Long Drain (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. Check dispenser motor for powered rotations. Up next Maytag Oven Error Codes - Duration: 3:04. and 8 p.m.

F6/F7/F8/F9 Error codes F6 through F9 indicate circuit problems. Have you ever purchased from PartSelect.com before? This code is not listed in any of the error code lists I have seen. Sign in to make your opinion count.

Replace control board (clock). Replace failed component. Replace failed component. F11 - Serial Communication Error between MCU and CCU - Disconnect power and unplug unit.

How to Unlock a KitchenAid Electric Superba Range KitchenAid Superba oven ranges, known as the Architect Series, have a locking mechanism on the control pad. Luckily, this also means that a new control panel is covered under the limited warranty and I will only have to pay for the labor and diagnosis fee. If error continues, replace touch control module. I ran a test on all burners and they all appar to operate atleast for a 1 minute test each.

The Reset Sequence for a KitchenAid Dishwasher KitchenAid Dishwasher Error Codes; Comments. Sign in Transcript Statistics 3,148 views Like this video? Loading... Press and HOLD start to continue the cycle, or press off/pause to clear display.