Home > Error Code > Kitchenaid Oven Error Codes

Kitchenaid Oven Error Codes

Contents

F10 Motor control unit (MCU) heat sink thermal trip If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. Select the 'cancel' function and wait 60 seconds. Replace failed component. ^ top F13 Dispenser circuit error If the dispenser motor is not able to be driven to its proper position. Source

Check the pressure switch for proper operation. Clean the glass surface and remove all objects placed on it. 2. Possible Causes / Procedure 1. Check probe. check these guys out

Kitchenaid Oven Error Code F2e1

Disconnect power for at least 30 seconds. 2. Check the drive system for any worn or failed components. 4. Possible Causes / Procedure • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check For SELF CLEAN models, check door lock operation.

E1 - Open Temperature Sensor - Replace temperature sensor. Fault Codes Fault Codes Admiral Bosch Dacor Estate Frigidaire GE Gibson Hotpoint Jenn Air Kelvinator Kitchen Aid Magic Chef Maytag Roper Sears / Kenmore Tappan Thermador Whirlpool We are Safe, Secure, Replace failed component. Kitchenaid Oven Error Code F2e1 Stuck Shorted Key F10 - Motor Control Unit (MCU) Heat Sink Thermal Trip (Too Hot) - Check for proper installation and ventilation, and make sure unit is not located near a heat source.

Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes. Kitchenaid Refrigerator Error Codes Check the MCU by looking for operations of the drive motor. 6. Unplug washer or disconnect power. 2. http://www.appliancepartspros.com/repair-help/kitchenaid-fault-codes.html Possible Causes / Procedure • Door lock mechanism is broken. • Door switch/lock unit failure. 1.

If connections are ok, then check individual switches as outlined for the F5 error code. Kitchenaid Dishwasher Error Codes Replace failed component. In an overflow condition, the door remains locked and the drain pump runs constantly, even if PAUSE/CANCEL is pressed twice and the display is cleared. F10 Motor control unit (MCU) heat sink thermal trip If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink

Kitchenaid Refrigerator Error Codes

Unplug washer or disconnect power. 3. my response codes. Kitchenaid Oven Error Code F2e1 Replace failed component. Kitchenaid Oven Error Code F2e0 Replace failed component.

Reply With Quote November 12th, 2006,12:08 PM #4 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location McMullen Valley, Arizona Posts 79,624 Ok, this contact form A tech is coming out in two days and hopefully it will finally clear up the problem. F14 EEPROM error The Central Control Unit (CCU) receives its data from an EEPROM onboard the CCU. Reconnect the unit and power to verify the pressure switch is operational, as well as the flow meter (blow air through the flow meter and measure resistance). Kitchenaid Oven Error Code F6e0

codes. F2 - E3 Keypad held down too long, or keypad is shorted. Replace pressure switch. have a peek here Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 4.

F22 Key sensitivity problem 1. Kitchenaid Oven Error Code F9e0 Replace control. Reconnect power. 3.

Replace failed component. ^ top F07 Motor control unit error The main control has detected a short in the Motor Control Unit.

Your satisfaction is important to Sears. Please try again later. Click here for more information on other Kitchen Aid Parts from PartSelect.com Back to top Tweet PartSelect.com Home Contact About Us Help Privacy Policy Terms of Use Just For Fun! Kitchenaid Error Code F8e0 Possible Causes / Procedure • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check

Cooktop KECC508MBL Failure Indication Failure Code Fault Code Description Solution F03 One or more keys permanently pressed 1. Check all hoses for possible leaks. 5. Check connections to the water temperature sensor. 3. Check This Out If failure remains, replace the touch control module.

If failure remains, replace the touch control module. The wires should be to the left when facing the MCU connectors. Press Start to continue the cycle, or press Pause/Cancel to clear the display. Sign in to make your opinion count.