Home > Error Code > Kitchenaid Oven Error Code F2e1

Kitchenaid Oven Error Code F2e1

Contents

Check sensor, sensor harness, and the sensor harness connection at sensor and oven control. The call rep said that the error code meant that the control board was malfunctioning, which was already obvious, and that the problem was solely with the control board/keypad. Check for any cracks or holes in the washer tub or pressure switch hose. I am not sure if this unit uses a seperate membrane switch for the keypad or if it is one unit. Source

If there is NO water in the unit, make sure the valves are turned on all the way. Note: Unit will attempt to unlock itself during this error six times before displaying this error code. F1 - Control Board Failure - Replace control board (clock). I hit start to clear the PF. find more info

Kitchenaid Oven Error Code F2e1 Stuck Shorted Key

F22 - Key Sensitivity Problem - Disconnect power for one minute and check to see if error reappears once power has been restore. By rv8 in forum KitchenAid Replies: 1 Last Post: January 26th, 2006, 01:22 AM Kitchenaid Free Standing Icemaker KUISI5NRHB6 By rsirmans in forum Undercounter / Freestanding / Stand Alone Ice Makers Make sure the serial harness at the MCU is not mounted upside down. Valid for standard ground shipping within the continental United States and not valid for shipments to Alaska, Hawaii, Puerto Rico, Guam and the US Virgin Islands.

spelunkerd 137,635 views 15:06 E4,E5,E6,F1,F2,F3 - Duration: 2:25. It is normal to see darker areas around the resistors on the board. The tech sheet lists this code as invalid cancel key. Kitchenaid Oven Error Code F6e0 Do I pay you or pat myself on the back?

Check the drive belt and reconnect power and plug unit in. F2-E1 - Touch Pad Cable Unplugged - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). http://www.kitchenaid.com/customer-service/faqs/my-dishwasher-won't-drain/PH3695/ All F5-E Codes - Door Switch Defect - This occurs when the door switches do not match.

It's fast and easy to create one. Kitchenaid Oven Error Code F9e0 From when I pulled it out and looked at the wiring in the back before, it didn't look like any of the wires had burned out or were worn. Select the 'cancel' function and wait 60 seconds. To post questions, help other DIYers and reduce advertising (like the one on your left), join our DIY community.

Kitchenaid Oven Error Code F2e0

F06 - Drive Motore Tachometer Error (Unable to Detect Motor Speed) - Check the shipping system including shipping bolts, spacers, and cables are removed and unplug unit and disconnect power. http://www.appliancepartspros.com/repair-help/kitchenaid-fault-codes.html Showing 0 of 0 items Subtotal: (before Tax and Shipping) View CartContinue Shopping SHOP OUTLET LIVE CHAT MAJOR APPLIANCES COUNTERTOP APPLIANCES KITCHENWARE FIND A RETAILER CONTACT US Stores Search Use my Kitchenaid Oven Error Code F2e1 Stuck Shorted Key Proceed by checking the drain hoses for proper connection and kinks. Kitchenaid Refrigerator Error Codes Home Service & Support Product Help Product Help Return to Search Results Print No results were found.

I ran the test as I described, and as I suspected, the oven did NOT error out when I removed the membrane switch ribbon cable from the control board while the this contact form Note: This error may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. I then tried to test the oven and set it to bake at default 350 which it ran at for less than a minute and then shut down with error code Verify that the inlet valve is operational. F2e1 Whirlpool Oven

If not, something could have shorted and damaged the board. 03-31-07,06:37 AM #7 LandToSea Member Join Date Mar 2007 Posts 14 Yes it was off. F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect. It is also possible that the electronic control board or console electronics has failed. have a peek here Working...

Check the drive system for any worm or failed components and reconnect power and plug unit in. Kitchenaid Error Code F8e0 Then when I powered up it caused the short and may cause he new board to do the same! All rights reserved.

Here is the line copied from your techsheet.

Check the electrical connections at the pump and make sure it is operational with no debris or blockage. Gently pull the tab down approximately 1/4 inch or until a 'click' is heard. SUD - Suds Lock (Too Much Detergent Detected) - Make sure drain hose is not plugged or kinked and disconnect power and unplug unit. Kitchenaid Oven Pf Error Verify Central Control Unit (CCU) is operating properly by running a diagnostic test or any cycle.

AppliancePartsPros 24,563 views 3:34 Checking an Oven Temperature Sensor - Duration: 3:58. You could be looking at a new control board anyway. 03-30-07,05:03 AM #3 LandToSea Member Join Date Mar 2007 Posts 14 Oh no! The customer purchased a replacement control board and the error persists, and called me. Check This Out A tech is coming out in two days and hopefully it will finally clear up the problem.

open the oven door and remove screws from the bottom of the control panel. You may freely link to this site, and use it for non-commercial use subject to our terms of use. Appliance Princess 1,126 views 3:04 KitchenAid Probe Fix KitchenAid Model KEBS207SSS00 - Duration: 1:57. Discover More Culinary Bundles Pro Line Series Stand Mixers Stand MixerAttachments Food Processors Coffee Products Juicers Sparkling BeverageMaker by SodaStream Blenders Hand Blenders Hand Mixers Slow Cookers andMulti-Cookers Countertop Ovens Toasters

Note: If this error occurs, the door will remain locked and the drain pump will run constantly even if 'cancel' is selected. Learn More guaranteed fit All parts are manufacturer-approved, to ensure proper fit and to keep appliances running for years to come. Check wire harness connections to the Central Control Unit (CCU) and the dispenser motor. Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes.

Once the F2 code appears, select 'cancel' and observe for one minute for errors. Press and HOLD start to continue the cycle, or press off/pause to clear display.