Home > Error Code > Kitchenaid Microwave Error Codes

Kitchenaid Microwave Error Codes

Contents

Unplug washer or disconnect power. 3. Replace is defective. Unplug washer or disconnect power. 2. Unplug washer or disconnect power. 2. Source

Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). 3. Ask Anonymously Popular Products GE Spacemaker JVM1640SJ Microwave Oven 1 Questions GE Advantium 120 Convection/Microwave Oven 6 Questions GE XL1800 1100 Watts Microwave Oven 1 Questions GE JVM1650 1000 Watts Microwave Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves. For SELF CLEAN models, check door lock operation. http://www.appliancepartspros.com/repair-help/kitchenaid-fault-codes.html

Kitchenaid Oven Error Code F2e1

Check the MCU by looking for operations of the drive motor, and check drive motor for powered rotations. Plug in washer or reconnect power. 5. F6-E0 - Return Line Not Connected - This error should appear within 60 seconds after power up to appliance. Check the drive system for any worn or failed components and reconnect power and plug unit in.

Look for condensation or contamination on probe receptacle. Replace failed component. Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU). Kitchenaid Oven Error Code F2e1 Stuck Shorted Key Measure door switch (door open = switch open small low voltage terminals).

Make sure there is not a siphon problem and check all hoses for possible leaks. Check MCU by looking for operations of the drive motor and check drive motor for powered rotations. It will try to unlock the door six times before displaying the error code. over here F36 - Temperature Probe Hardware Error - Disconnect power for one minute and check to see if error reappears once power has been restore.

The only thing that I could think of is, was power to the unit disconnected while you were installing the top? Kitchenaid Oven Error Code F9e0 Possible Causes / Procedure • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Getting your parts... 24/7 Customer Support Call 1-877-477-7278 Sign In About Us Repair Forum My Account Order Status Shop for Parts Get Repair Help CHECKOUT Items in Cart: Total $0.00 Dishwasher

Kitchenaid Refrigerator Error Codes

Plug in microwave oven or reconnect power.

Replace switch if defective. 4. Kitchenaid Oven Error Code F2e1 Check the drain hose and make sure it is not plugged or kinked. 2. Kitchenaid Oven Error Code F2e0 If error continues, replace touch control module.

F11 Serial communication error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. this contact form Check the drive motor for powered rotations. E1 - Open Thermistor - Replace thermistor. Check the drive motor for powered rotations. Kitchenaid Oven Error Code F6e0

If failure remains, disconnect power for one minute. F02 Long drain If the drain time exceeds eight minutes, the water valves are turned off and "F02" is flashed. Check mechanical linkage from dispenser motor to the top of the dispenser. 3. have a peek here Replace failed component. ^ top F13 Dispenser circuit error If the dispenser motor is not able to be driven to its proper position.

Check keypad connector for firm connection (keypad connects to control board). 2. Kitchenaid Dishwasher Error Codes If error still remains after power has been restored, replace touch control module. (control board) F12 - Electronic Board and Touch Module Communication Error - Disconnect power for one minute and Check the MCU by looking for operations of the drive motor. 7.

Possible Causes / Procedure 1.

Verify CCU operation by running a Diagnostic test or any cycle. 6. Measure the lower oven temperature sensor resistance using a volt/ohm meter. If failure remains, replace the touch control module. Kitchenaid Microwave Error Code F2e1 Possible Causes / Procedure 1.

Check resistance of heating element, if present on this model. (abnormal = infinity). Unplug washer or disconnect power. 2. I can not find this specific error code anywhere in any posted error code lists??? Check This Out I was just hoping it was repairable.

Verify CCU operation by running a Diagnostic test or any cycle. I have a Kitchenaid Range model KERC507HBS3. If corrections are made in any step, reconnect power to control. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 3.

F3 Oven temperature sensor (RTD) open Replace Oven temperature sensor (RTD) F4 Oven temperature sensor (RTD) shorted Replace Oven temperature sensor (RTD) F5 Board failure Replace control board (also called ERC Check all hoses for possible leaks. 5. Kansas City, KS "Robin went above and beyond the call to assist me and I was very impressed." Val T. Possible Causes / Procedure • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check

Possible Causes / Procedure • Door lock mechanism is broken. • Door switch/lock unit failure. 1. If all connections are good, then check the individual switches as outlined for the F5 failure. ^ top 2 Digit Failure Codes F0 Board failure Replace control board (also called ERC Mesquite, TX "When you say 'Fast Shipping', you aren't kidding!" Warnie M. Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves.

If failure remains, replace the touch control module. Check connections at control and at the latch switch and door switch. 2. Verify CCU operation by running a Diagnostic test or any cycle. Showing 0 of 0 items Subtotal: (before Tax and Shipping) View CartContinue Shopping SHOP OUTLET LIVE CHAT MAJOR APPLIANCES COUNTERTOP APPLIANCES KITCHENWARE FIND A RETAILER CONTACT US Stores Search Use my

F13 Internal CPU checksum errors 1.