Home > Error Code > Kitchenaid Kgst307hbs9 Error Code

Kitchenaid Kgst307hbs9 Error Code

Contents

Make sure the serial harness at the MCU is not mounted upside down. Replace failed component. E3 - User Interface or Software Mismatch - If this error code appears, there is a user interface or software mismatch. Discover More Black Stainless Cooktops Wall Ovens Refrigerators UndercounterRefrigerators Ranges Microwaves Dishwashers Disposers & Compactors Warming Drawers Hoods & Vents Grills Water Filters Accessories Accessories Cooktops Dishwashers Hoods & Vents Microwaves Source

If door is latched, disconnect power from unit and check wires and connections. F9 - Oven Door Lock Failure - Check door lock switches and wiring. KitchenAid Pro Line Front Loading Gas and Electric Dryer Fault Codes (Models KHEV01RSS and KHGV01RSS) PF - Power Failure - PF error code indicates a power failure during the dryer's cycle. Replace failed component. click resources

Kitchenaid Error Code F2e1

F02 - Long Drain (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. Unplug the unit and disconnect the power to check all wire harness connections to the inlet valve, pressure switch, drain pump, flow meter, and Central Control Unit (CCU).

Check the door switch/lock for any debris or foreign objects. F13 - Dispenser Circuit Error - Disconnect power and unplug unit to check mechanical linkage from dispenser motor to top of dispenser. If error continues, replace board connection cable between touch control module and electronic control. Kitchenaid Oven Error Code F6e0 Verify CCU is working by performing diagnostic test or any cycle.

F1-E6 - Latch Signal Mismatch Error - Disconnect power for at least 30 seconds and then reconnect. Kitchenaid Oven Error Code F2e1 Stuck Shorted Key Proceed by checking the drain hoses for proper connection and kinks. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. F4-E1 -Meat Probe Defect - This error indicates a problem with either the probe, receptacle, or probe circuit.

If connections are not damaged, reconnect power and hold down any key until the F5 error clears. Kitchenaid Oven Pf Error Reconnect power and plug unit in. F2 - Oven Temperature Is Too High - Check for welded contacts on bake and broil relays. E5 - Dry Rack Sensor - If the signal is lost during a Dry Rack cycle, all outputs will be turned off and this error code will appear.

Kitchenaid Oven Error Code F2e1 Stuck Shorted Key

Check the drive belt and reconnect power and plug unit in. click site Note: Unit will attempt to unlock itself during this error six times before displaying this error code. Kitchenaid Error Code F2e1 Make sure the drain pump is free from debris or foreign objects and then reconnect power and plug unit in. Kitchenaid Refrigerator Error Codes The door should now be unlocked.

Discover More Culinary Bundles Pro Line Series Stand Mixers Stand MixerAttachments Food Processors Coffee Products Juicers Sparkling BeverageMaker by SodaStream Blenders Hand Blenders Hand Mixers Slow Cookers andMulti-Cookers Countertop Ovens Toasters this contact form If there is water in the unit, verify the drain pump is working and the pressure switch hose is in good condition and properly connected. If error continues, replace electronic control (control board) and if error still persists, replace the touch module (touch pad). Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves. Kitchenaid Oven Error Code F2e0

F33 - System Leak - Select 'cancel' twice to clear error code. Check the door switch/lock for any debris or foreign objects. By rv8 in forum KitchenAid Replies: 1 Last Post: January 26th, 2006, 01:22 AM Kitchenaid Free Standing Icemaker KUISI5NRHB6 By rsirmans in forum Undercounter / Freestanding / Stand Alone Ice Makers have a peek here Check dispenser motor for powered rotations.

Need help? Kitchenaid Oven Error Code F9e0 F09 - Overflow Condition (Pressure Switch Closed Too Long) - Check to make sure drain hose is not plugged or kinked and unplug the unit and disconnect power. and elsewhere. ???DISCONTINUED_PRODUCT_DIALOG_INSTRUCTIONS???

F13 - Dispenser Circuit Error - Disconnect power and unplug unit to check mechanical linkage from dispenser motor to top of dispenser.

Replace is defective. All rights reserved. Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves. Kitchenaid Dishwasher Error Codes No parts to buy or anything, just my free labor.

F05 - Water Temperature Sensor Error - Unplug and disconnect power to the unit and check connections to the water temperature sensor. Check the drive system for any worm or failed components and reconnect power and plug unit in. ChristianPlymouth,MN. Check This Out Log in to Reply Mason on November 15, 2011 at 11:31 pm Thanks so much for the GREAT and very USEFUL tips!

Disconnect power and unplug the unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU). F1-E9 - Stack Overflow - Disconnect power for at least 30 seconds and then reconnect. We have a special program here, all parts you order from our links we post are returnable within 365 days for a FULL refund(minus shipping back) if they don't fix the and elsewhere. ???DISCONTINUED_PRODUCT_DIALOG_INSTRUCTIONS???

The KitchenAid Shop site is temporarily down. Sometimes it will show up 25-40 min after I start cooking something, sometimes it will show up when I close a nearby cupboard door or tap a spatula forcefully against the Just wanted to write and say thank you! I enjoy diagnosing appliance failures, but some times its nice to follow the path to the failure.

Verify CCU is working by performing diagnostic test or any cycle. If error reappears, replace touch pad, or touch and pad and control board (clock) if all one assembly. Note: You may see a "SUD" error code appear first during this failure. We’re sorry.

Replace failed component. Reconnect power and plug unit in. Note: Double ovens will have two of each switch and one common wire. 2 Digit Failure Codes F0 - Control Board Failure - Replace control board (clock). Reconnect power and plug unit in.

Check the electrical connections at the pump and make sure it is operational with no debris or blockage.