Kitchenaid Error Message
Appliance Princess 10,747 views 1:52 Whirlpool Oven Error Codes - Duration: 3:12. Verify CCU is working by performing diagnostic test or any cycle. Check wire harness connections to the motor, Motor Control Unit (MCU), and Central Control Unit (CCU). F07 - Motor Control Unit (MCU) Error - Unplug unit and disconnect power to check wire harness connections between drive motor and MCU, and between MCU and Central Control Unit (CCU). Source
Sign in Don't like this video? Some exceptions apply.Learn how our pricing differs from other firms. $169 Home About Us Corporate Profile Key Benefits Careers Testimonials Repair Services Why Repair Your Timer? Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & Welcome to the DoItYourself Forums! http://www.partselect.com/JustForFun/Kitchen-Aid-Appliance-Fault-Codes.aspx
Kitchenaid Refrigerator Error Codes
Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & If error continues, replace touch control module. Oven elements, Electronic oven control board F6/E2 Oven too hot in Clean mode If an element heats when the oven is off (indicating a short to the metal cabinet), replace it. We must receive the returned part(s) with the Return Authorization number within 365 days of your original order date.
Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab. The design of the stand mixer is a trademark in the U.S. Sign up here Find a Professional Type of Job Type of Job Additions and Remodels Appraisers and Home Inspectors Architects Bathroom Remodeling Cabinets and Countertops Carpentry Carpet Cleaning Concrete and Masonry Kitchenaid Dishwasher Error Codes The design of the stand mixer is a trademark in the U.S.
Check the wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit. Kitchenaid Oven Error Code F9e0 If connections are not damaged, measure door switch (door open = latch open) and latch switch (unlatch = switch open) and replace either if defective. Replace failed component. All sounds normal so far?
Kitchenaid Oven Error Code F2e1 Stuck Shorted Key
Sears Holdings reserves the right to terminate or modify this offer at any time for failure to comply with its terms and/or due to any operational malfunction of the software, hardware http://www.applianceblog.com/mainforums/threads/6276-KitchenAid-Range-Oven-F2-E1-Error-Ignitor-problems Clearing your browser history may delete your saved models. Kitchenaid Refrigerator Error Codes Remember: The oven control board (clock) measures resistance of sensor circuit, not actual oven temperature. Kitchenaid Oven Error Code F2e0 Press and HOLD start to continue the cycle, or press off/pause to clear display.
Replace failed component. this contact form I can not find this specific error code anywhere in any posted error code lists??? Check the drive system for any worm or failed components and reconnect power and plug unit in. I have a Kitchenaid Range model KERC507HBS3. Kitchenaid Oven Error Code F6e0
Your satisfaction is important to Sears. F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect. Credit will be issued for the part(s) plus tax, minus shipping charges. http://jvmwriter.org/error-code/kitchenaid-f2-e3-error.html Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
Note: Unit will attempt to unlock itself during this error six times before displaying this error code. Kitchenaid Error Code F8e0 Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves. Check the door switch/lock for any debris or foreign objects.
Replace failed component.
Appliance Princess 10,903 views 2:43 Range Oven F1 Error Repaired - Duration: 11:02. The cancel button is one of the buttons not currently functuning. Pull the bottom toward you while lifting up to remove the panel from the top of the side rails. Kitchenaid Oven Pf Error I provided a page from the tech sheet in the first image below that shows information on that error code. I recommend that you shut off the circuit breaker for 5
Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes. TechnicianBrian TechnicianBrian.com AllTechAppliance.com Reply With Quote May 12th, 2010,08:33 PM #7 unkapete View Profile View Forum Posts Member Join Date May 2010 Location nj Posts 1 The fix seems to have I hit start to clear the PF. Error code F2 E1 on Kitchenaid?
F4 - Shorted Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD). I would appreciate any advice you could give me on how to fix the problem, it has made cooking next to impossible for me, and I want to avoid calling a Note: You may see a "SUD" error code appear first during this failure. This code is not listed in any of the error code lists I have seen.
To manually unlock the unit, unplug the power cord from the outlet and remove the toe panel. Learn More for questions or assistance, call 1-800-252-1698 (Se Habla Español) M-F6:30 a.m. - 10:00 p.m. to be bought in 02'. Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves.
Sign in Transcript Statistics 3,148 views Like this video? F1-E9 - Stack Overflow - Disconnect power for at least 30 seconds and then reconnect. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. F11 - Serial Communication Error Between MCU and CCU - Disconnect power and unplug unit.
It's free! Press and hold any key to clear the error code and F2 code should appear. The only thing that I could think of is, was power to the unit disconnected while you were installing the top? If error still remains after power has been restored, replace touch control module. (control board) F12 - Electronic Board and Touch Module Communication Error - Disconnect power for one minute and