Kitchen Aid Supra Error Codes
Check the drain hose and make sure it is not plugged or kinked. 2. Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves. Check/clean drain pump filter of foreign objects. 5. FdL Door lock error A Door Lock Error occurs if the door cannot be locked.
Kitchenaid Error Code F2e1
Replace failed component. Meer weergeven Laden... Replace the pump. ^ top F05 Water temperature sensor error If during the water heating step in the wash cycle, the water temperature sensor (NTC) value is out of range, the Recently Visited () Getting your parts... 24/7 Customer Support Call 1-877-477-7278 Sign In About Us Repair Forum My Account Order Status Shop for Parts Get Repair Help CHECKOUT Items in Cart:
E1 Thermistor open Replace thermistor if found defective E2 Thermistor shorted Replace thermistor if found defective E3 User interface or software mismatch This error code will ONLY appear when in the Make sure the serial harness at the MCU is not mounted upside down. Unplug washer or disconnect power. 2. Kitchenaid Oven Error Code F2e1 Stuck Shorted Key Plug in washer or reconnect power. 6.
User interface F1/E1 Electronic oven control board failure Disconnect electrical power from the oven and replace the electronic oven control board. Press CANCEL. Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle.
Reconnect any loose wires on the oven door switch and the oven door lock assembly.
Replace failed component. Kitchenaid Dishwasher Error Codes Check wire harness connections to the touchpad/LED assembly and Central Control Unit (CCU). Unplug washer or disconnect power. 2. Measure the lower oven temperature sensor resistance using a volt/ohm meter.
Kitchenaid Refrigerator Error Codes
VideoJoeKnows 33.423 weergaven 10:46 Frigidaire Oven Error Codes - Duur: 2:56. http://www.appliancetimers.com/failure-code-page?manufacturer=ka&type=r Press CLEAN. 3. Kitchenaid Error Code F2e1 Check that the pressure switch is operational and replace if defective. Kitchenaid Oven Error Code F6e0 Disconnect power and unplug unit to check wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit.
Gently pull the tab down approximately 1/4 inch, or until a click is heard. 5. http://jvmwriter.org/error-code/l4000-error-codes.html Login | FAQ + Reply to Thread Results 1 to 8 of 8 LinkBack LinkBack URL About LinkBacks Thread Tools Show Printable Version Search Thread Advanced Search Display Linear Mode Enjoy bottle-quality water without the added waste (stays the same) Automatic Reorder About SYWR Get rewarded for shopping. Powered by vBulletin™ Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. Kitchenaid Oven Error Code F2e0
Press PAUSE/CANCEL twice to clear the display. Replace failed component. Possible Causes / Procedure • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check http://jvmwriter.org/error-code/kitchen-aid-error-code.html F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect.
F21 / F22 - Central Control Unit (CCU) / Touch Pad / LED Assembly Error - Check that the touch pad/LED assembly is working by selecting different cycles and changing the Kitchenaid Oven Error Code F9e0 Check the drain pump filter for foreign objects. 5. FdU - Door Unlock Error - It is possible the door lock mechanism is broken or the door switch/lock unit has failed.
If there is NO water in the unit, make sure the valves are turned on all the way.
WeergavewachtrijWachtrijWeergavewachtrijWachtrij Alles verwijderenOntkoppelen Laden... Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). 3. If failure remains, disconnect power for 1 minute. 3. Kitchenaid Error Code F8e0 Replace failed component.
If connections are not damaged, measure door switch (door open = latch open) and latch switch (unlatch = switch open) and replace either if defective. Press CANCEL and observe for 1 minute to ensure operation is correct. 6. Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Check This Out Find Parts Kitchen Aid Built-In Microwave Oven Fault Codes Failure Code Fault Code Description Solution F1 - E3 or F1 - E4 Electronic control malfunction Replace control.
OR If the control has turned the water valves on, and after 8 minutes, the flow sensor has detected 10.5 gallons of water passing through it, but has not detected the Replace failed component. codes except F1-E3. Unplug washer or disconnect power. 3.