Home > Error Code > Kitchen Aid Error Code

Kitchen Aid Error Code


If error still remains after power has been restored, replace touch control module. (control board) F12 - Electronic Board and Touch Module Communication Error - Disconnect power for one minute and Unplug washer or disconnect power. 2. I then tried to test the oven and set it to bake at default 350 which it ran at for less than a minute and then shut down with error code The wires should be to the left when facing the MCU connectors. Source

Re-apply power and observe for at least one minute. 3. Thanks! Laden... The ones which are not working now do not seem as bubbled out as the ones which do respond to pushing them. http://www.partselect.com/JustForFun/Kitchen-Aid-Appliance-Fault-Codes.aspx

Kitchenaid Oven Error Code F2e1

Check that the serial harness at the MCU is not mounted upside down. You can try checking the door switch, check the latch for interference –A broken door hinge or loose door seal in the way would be obvious.And if that isn’t it, power Log in to Reply Anonymous on September 24, 2011 at 12:12 pm This worked perfectly!!! Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes.

If the wire harness connections are okay, replace the user interface. F12 Electronic board and touch module communication error 1. NOTE: After four minutes the "Sud" error will be displayed, then four minutes later the "F02" error code will be displayed.. Kitchenaid Oven Error Code F2e1 Stuck Shorted Key Your expertise and kindness to share your solution just helped us out immensely.

Verify CCU operation by running a Diagnostic test or any cycle. Login to DoItYourself Username: Password: Forgot username or password? Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 4. To manually unlock the unit, unplug the power cord from the outlet and remove the toe panel.

Repeat steps A and B for door switch. 3. Kitchenaid Dishwasher Error Codes Appliance Princess 3.582 weergaven 2:38 Kitchenaid & Whirlpool Wall Oven Diagnostic - Does Not Bake or Broil - KEBC247VSS02 - Duur: 6:19. Possible Causes / Procedure 1. F36 Temperature probe hardware error 1.

Kitchenaid Refrigerator Error Codes

Adam Davenport 3.563 weergaven 5:34 Homemade Wood-Fired Pizza Oven Cost Nothing At All To Build (And Feeds Small Multitude) - Duur: 5:21. Error codes on appliances are provided as a way to first, show something is wrong, and second, hopefully point the customer in the right direction for a solution. Kitchenaid Oven Error Code F2e1 Check dispenser motor for powered rotations. Kitchenaid Oven Error Code F6e0 If connections are not damaged, reconnect power and hold down any key until the F5 error clears.

To be covered by the warranty, the refrigerator must have been purchased within the prior 12 months, while the specific nature of the extended service plan should be verified through the this contact form Since I had never done this before it did not go as smooth as it could have, but I got it completed without breaking the new top. Verify there is not a siphon problem. 2. F09 - Overflow Condition (Pressure Switch Closed Too Long) - Check to make sure drain hose is not plugged or kinked and unplug the unit and disconnect power. Kitchenaid Oven Error Code F2e0

Meer weergeven Laden... Sign up here Find a Professional Type of Job Type of Job Additions and Remodels Appraisers and Home Inspectors Architects Bathroom Remodeling Cabinets and Countertops Carpentry Carpet Cleaning Concrete and Masonry E5 - Dry Rack Sensor - If the signal is lost during a Dry Rack cycle, all outputs will be turned off and this error code will appear. have a peek here The electric control unit is all one piece and looks like it runs at least $255!

The unit would power up and display the PF to the left display and also the time from when previously powered on. Kitchenaid Oven Error Code F9e0 Possible Causes / Procedure • Door lock mechanism is broken or removed from door. • Door switch/lock unit failure. 1. F4 - Shorted Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD).

Continue Reading Keep Learning How many KitchenAid refrigerator models are there?

Possible Causes / Procedure • Door lock mechanism is broken or removed from door. • Door switch/lock unit failure. 1. Q: How can you find a guide on refrigerator troubleshooting? Looking for a Specific Part? Kitchenaid Error Code F8e0 E6 - Exhaust High Limit Fault - If exhaust temperature rises above 87.7 degrees Celcius (190 degrees Fahrenheit), all outputs will be turned off and this error code will appear.

Check the drive motor for powered rotations. Unplug washer or disconnect power for two minutes. 2. E4 Tumbler rotation failure If during a cycle the tumbler rotational speed drops to 0, all outputs will be turned off and error code E4 will be displayed. Check This Out Unplug washer or disconnect power. 2.

Note: This error may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. Verify CCU is working by performing diagnostic test or any cycle. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). F5 - E6 Door is open, but latch is locked F5 - E7 Self clean latch will not unlock F6 - E0 Return line not connected If switch pulse return line